Lecture 26Review: Current MirrorsReview: Current Mirrors (cont’d)Slide 4Base-emitter ReferenceBase-emitter Reference (cont’d)Self BiasingSelf Biasing (cont’d)Start-up CircuitStart-up Circuit (cont’d)Slide 11MOSFET Current SourceMOSFET Current Source (cont’d)Slide 14Slide 15ReferencesGuest Lecturer: Prof. Ali NiknejadEE105 Fall 2007 Lecture 26, Slide 1 Prof. Liu, UC BerkeleyLecture 26OUTLINE• Self-biased current sources–BJT–MOSFET•Guest lecturer Prof. NiknejadANNOUNCEMENTS•Homework 12 due Thursday, 12/6EE105 Fall 2007 Lecture 26, Slide 2 Prof. Liu, UC BerkeleyReview: Current Mirrors•The current mirrors we discussed require a “golden” current source, IREF, to copy.EE105 Fall 2007 Lecture 26, Slide 3 Prof. Liu, UC BerkeleyReview: Current Mirrors (cont’d)•In lab 6 and lab 10, you used a resistor as your current source. •Q: What are some problems associated with this method?EE105 Fall 2007 Lecture 26, Slide 4 Prof. Liu, UC BerkeleyReview: Current Mirrors (cont’d)•A: Variations in VCC and temperature cause significant variations in IREF. Consider the following analysis (ignoring base currents and the Early effect):•Thus, a 10 % change in VCC results in a 11.6 % change in IREF.EE105 Fall 2007 Lecture 26, Slide 5 Prof. Liu, UC BerkeleyBase-emitter Reference•Rather than having a source dependent on VCC, why not use some other reference?•For example, a VBE referenced current source.•Ignoring base currents, we have:•Q: Why is this less supply dependent?EE105 Fall 2007 Lecture 26, Slide 6 Prof. Liu, UC BerkeleyBase-emitter Reference (cont’d)•A: Although IIN varies almost directly with VCC, VBE1 won’t vary nearly as much, since the device is exponential. Since IOUT depends only on VBE1, the output won’t vary much with VCC.•Example:•Assuming VBE1 = 0.7 V, a change in input current by 10X causes an output current change of 8.7 %.EE105 Fall 2007 Lecture 26, Slide 7 Prof. Liu, UC BerkeleySelf Biasing•We can do better than the VBE referenced source using feedback. What if our source had a current mirror attached that fed back the output current to act as the input current?EE105 Fall 2007 Lecture 26, Slide 8 Prof. Liu, UC BerkeleySelf Biasing (cont’d)•Here, we’ve attached a pnp current mirror to force IOUT and IIN to match.•There are two stable operating points:–IIN = IOUT = 0 A–Desired operating pointEE105 Fall 2007 Lecture 26, Slide 9 Prof. Liu, UC BerkeleyStart-up Circuit•Need a way to “start-up” the circuit, like a car starter starts up your car.•Requirements:–Must keep the circuit out of the undesired operating point–Must not interfere with the circuit once it reaches the desired operating pointEE105 Fall 2007 Lecture 26, Slide 10 Prof. Liu, UC BerkeleyStart-up Circuit (cont’d)EE105 Fall 2007 Lecture 26, Slide 11 Prof. Liu, UC BerkeleyStart-up Circuit (cont’d)•Let’s ensure this works:–Assume IIN = IOUT = 0. This means approximately that VBE1 = VBE2 = 0. However, note that the left side of D1 is four diode drops from ground, meaning D1 is on. This drops some voltage across Rx, forcing current to flow into T1 and T2, starting up the circuit.–After the circuit is at the desired operating point, turn D1 off by ensuring RxIIN (the drop across Rx) is sufficiently large.EE105 Fall 2007 Lecture 26, Slide 12 Prof. Liu, UC BerkeleyMOSFET Current Source•We can build an analogous circuit from MOSFETs as well. Let’s start with a VTH referenced current source.•If we make Vov1 small (by sizing up T1 or using small currents), IOUT is controlled primarily by VTH and R2.EE105 Fall 2007 Lecture 26, Slide 13 Prof. Liu, UC BerkeleyMOSFET Current Source (cont’d)•Let’s add the current mirror feedback.EE105 Fall 2007 Lecture 26, Slide 14 Prof. Liu, UC BerkeleyMOSFET Current Source (cont’d)•Finally, the start-up circuitry. It’s more typical to use more MOSFETs in MOS technologies rather than diodes.EE105 Fall 2007 Lecture 26, Slide 15 Prof. Liu, UC BerkeleyMOSFET Current Source (cont’d)•Assume IIN = IOUT = 0. This means VGS1 = 0, meaning T8 is in triode. This turns on T9 and forces current to flow into T4 and T5.•Once in steady state, we can size T7 to ensure that T9 turns off. T7 and T8 don’t directly affect the circuit themselves, so the start-up circuit has done its job.EE105 Fall 2007 Lecture 26, Slide 16 Prof. Liu, UC BerkeleyReferences•Material and figures largely from Analysis and Design of Analog Integrated Circuits, Fourth Edition by Gray, Hurst, Lewis, and Meyer.EE105 Fall 2007 Lecture 26, Slide 17 Prof. Liu, UC BerkeleyGuest Lecturer: Prof. Ali Niknejad•Faculty director of the Berkeley Wireless Research Center (BWRC). Primary research interests include analog integrated circuits, mm-wave CMOS, RF and microwave circuits, device modeling (BSIM), electromagnetics (ASITIC), communication systems, and scientific
View Full Document
Unlocking...