Whole Building Design Guide Federal Green Construction Guide for Specifiers This is a guidance document with sample specification language intended to be inserted into project specifications on this subject as appropriate to the agency s environmental goals Certain provisions where indicated are required for U S federal agency projects Sample specification language is numbered to clearly distinguish it from advisory or discussion material Each sample is preceded by identification of the typical location in a specification section where TM it would appear using the SectionFormat of the Construction Specifications Institute SECTION 10170 PLASTIC TOILET COMPARTMENTS SPECIFIER NOTE resource management Refer to Section 06600 Plastic Fabrications toxicity IEQ Refer to Section 06600 Plastic Fabrications performance Plastic partitions perform as well or better than most toilet partitions They are water resistant graffiti resistant and non absorbent with plastic face sheets permanently fused to plastic core PART 1 GENERAL 1 1 1 2 SUMMARY A Work Includes 1 Solid plastic toilet compartments floor mounted head rail braced xxxx 2 Solid plastic urinal screens wall mounted with floor mounted pilaster brace xxxx 3 Attachment hardware B Related Sections 1 Section 06100 Rough Carpentry Framing and plates within walls for partition attachment 2 Section 10810 Toilet Accessories Coordinate compartment installation with subsequent accessory installation REFERENCES A 1 3 American National Standards Institute ANSI 1 ANSI A117 1 Specifications for Making Buildings and Facilities Accessible To and Usable by Physically Handicapped People SUBMITTALS A Product data Unless otherwise indicated submit the following for each type of product provided under work of this Section SPECIFIER NOTE Green building rating systems often include credit for materials of recycled content USGBC LEED v2 2 for example includes credit for materials with recycled content calculated on the basis of preconsumer and post consumer percentage content and it includes credit for use of salvaged recovered materials Green Globes US also provides points for reused building materials and components and for building materials with recycled content 1 Recycled Content http fedgreenspecs wbdg org 11 02 05 10170 1 Plastic Toilet Compartments Whole Building Design Guide Federal Green Construction Guide for Specifiers a b c d Indicate recycled content indicate percentage of pre consumer and postconsumer recycled content per unit of product Indicate relative dollar value of recycled content product to total dollar value of product included in project If recycled content product is part of an assembly indicate the percentage of recycled content product in the assembly by weight If recycled content product is part of an assembly indicate relative dollar value of recycled content product to total dollar value of assembly SPECIFIER NOTE Specifying local materials may help minimize transportation impacts however it may not have a significant impact on reducing the overall embodied energy of a building material because of efficiencies of scale in some modes of transportation Green building rating systems frequently include credit for local materials Transportation impacts include fossil fuel consumption air pollution and labor USGBC LEED v2 2 includes credits for materials extracted harvested and manufactured within a 500 mile radius from the project site Green Globes US also provides points for materials that are locally manufactured 2 Local Regional Materials a Sourcing location s Indicate location of extraction harvesting and recovery indicate distance between extraction harvesting and recovery and the project site b Manufacturing location s Indicate location of manufacturing facility indicate distance between manufacturing facility and the project site c Product Value Indicate dollar value of product containing local regional materials include materials cost only d Product Component s Value Where product components are sourced or manufactured in separate locations provide location information for each component Indicate the percentage by weight of each component per unit of product B Submit environmental data in accordance with Table 1 of ASTM E2129 for products provided under work of this Section C Operating And Maintenance Manuals Submittals SPECIFIER NOTE The marking system indicated below is intended to provide assistance in identification of products for making subsequent decisions as to handling recycling or disposal 1 Verify that plastic products to be incorporated into the Project are labeled in accordance with ASTM D1972 Where products are not labeled provide product data indicating polymeric information in Operation and Maintenance Manual a Type 1 Polyethylene Terephthalate PET PETE b Type 2 High Density Polyethylene HDPE c Type 3 Vinyl Polyvinyl Chloride or PVC d Type 4 Low Density Polyethylene LDPE e Type 5 Polypropylene PP f Type 6 Polystyrene PS g Type 7 Other Use of this code indicates that the package in question is made with a resin other than the six listed above or is made of more than one resin listed above and used in a multi layer combination 1 4 QUALITY ASSURANCE A Regulatory Requirements Conform to ANSI A117 1 code for access for the handicapped operation of toilet compartment door and hardware PART 2 PRODUCTS http fedgreenspecs wbdg org 11 02 05 10170 2 Plastic Toilet Compartments Whole Building Design Guide Federal Green Construction Guide for Specifiers 2 1 MATERIALS A Solid plastic compartments and screens water resistant graffiti resistant nonabsorbent with plastic face sheets permanently fused to plastic core 1 thick panels unless otherwise indicated SPECIFIER NOTE US EPA Comprehensive Procurement Guidelines CPG recommend 20 100 percent post consumer recycled content for plastic toilet partitions 1 Recycled Content Minimum 20 xxxx percent post consumer recycled content B Pilaster Shoes 3 inches high Aluminum Stainless Steel One piece molded HDPE xxxx SPECIFIER NOTE Green building rating systems often include credit for materials of recycled content and may distinguish allowable credit for post consumer and post industrial or pre consumer recycled content USGBCLEED v2 2 for example factors 100 percent of post consumer recycled content but only 50 percent of pre consumer post industrial recycled content into calculations for its recycled content materials credit LEED v2 2 grants one credit to a project for using materials
View Full Document
Unlocking...