Whole Building Design Guide Federal Green Construction Guide for Specifiers This is a guidance document with sample specification language intended to be inserted into project specifications on this subject as appropriate to the agency s environmental goals Certain provisions where indicated are required for U S federal agency projects Sample specification language is numbered to clearly distinguish it from advisory or discussion material Each sample is preceded by identification of the TM of the typical location in a specification section where it would appear using the SectionFormat Construction Specifications Institute SECTION 07900 JOINT SEALANTS SPECIFIER NOTE resource management A variety of sealants single component and multi component are available for different applications There are few if any alternative agriculture or recycled content choices toxicity IEQ VOCs may be emitted during the curing process Generally sealants continue to outgas throughout their life Closed cell backer rods outgas when ruptured Open cell polyurethane backer rods are spongelike and may absorb moisture performance Performance is comparable for green methods and standard methods Sealants reduce air infiltration and moisture penetration Verify that the proper sealant is specified for the given application Improper selection can result in reapplication air infiltration water damage PART 1 1 1 GENERAL SUMMARY A 1 2 Section Includes 1 Interior joint sealants 2 Exterior joint sealants SUBMITTALS A Product data Unless otherwise indicated submit the following for each type of product provided under work of this Section SPECIFIER NOTE Specifying local materials may help minimize transportation impacts however it may not have a significant impact on reducing the overall embodied energy of a building material because of efficiencies of scale in some modes of transportation Green building rating systems frequently include credit for local materials Transportation impacts include fossil fuel consumption air pollution and labor USGBC LEED v2 2 includes credits for materials extracted harvested and manufactured within a 500 mile radius from the project site Green Globes US also provides points for materials that are locally manufactured 1 Local Regional Materials a Sourcing location s Indicate location of extraction harvesting and recovery indicate distance between extraction harvesting and recovery and the project site http fedgreenspecs wbdg org 11 02 05 07900 1 Joint Sealants Whole Building Design Guide Federal Green Construction Guide for Specifiers b c d Manufacturing location s Indicate location of manufacturing facility indicate distance between manufacturing facility and the project site Product Value Indicate dollar value of product containing local regional materials include materials cost only Product Component s Value Where product components are sourced or manufactured in separate locations provide location information for each component Indicate the percentage by weight of each component per unit of product SPECIFIER NOTE Green building rating systems may include credit for low emitting materials USGBC LEED v2 2 for example includes credits for low emitting materials including adhesives and sealants paints and coatings carpets and composite wood and agrifiber products Under LEED v2 2 adhesives and sealants are to comply with California s South Coast Air Quality Management District SCAQMD 1168 aerosol adhesives are to comply with Green Seal GS 36 interior architectural paints are to comply with Green Seal GS 11 anti corrosive paints are to comply with Green Seal GS 03 clear wood finishes are to comply with SCAQMD 1113 carpet with the Carpet and Rug Institute CRI Green Label Plus carpet cushion with CRI Green Label program and composite wood and agrifiber products are to contain no added urea formaldehyde As per USGBC published Credit Interpretations the credits for low emitting materials are directed towards interior site installed i e not prefabricated products Verify project requirements for low VOC products Both the Adhesive and Sealant Council ASC and the SCAQMD have indicated that low VOC adhesives may have performance difficulties in extreme temperature and humidity conditions Green Seal an independent non profit organization certifies low emitting products using internationally recognized methods and procedures Green Seal certification meets the criteria of ISO 14020 and 14024 the environmental standards for ecolabeling set by the International Organization for Standardization ISO the U S Environmental Protection Agency s criteria for third party certifiers of environmentally preferable products and the criteria for bona fide ecolabeling bodies of the Global Ecolabeling Network 2 VOC data a Architectural Sealants 1 Submit manufacturer s product data for sealants Indicate VOC limits of the product Submit MSDS highlighting VOC limits 2 Submit manufacturer s certification that products comply with Bay Area Resources Board reg 8 rule 51 B Submit environmental data in accordance with Table 1 of ASTM E2129 for products provided under work of this Section PART 2 2 1 PRODUCTS MATERIALS A Architectural Sealants 1 Toxicity IEQ a Comply with applicable regulations regarding toxic and hazardous materials and as specified Sealants must meet or exceed requirements of Bay Area Resources Board reg 8 rule 51 b Sealants containing aromatic solvents fibrous talc formaldehyde halogenated solvents mercury lead cadmium chromium and their compounds are not permitted http fedgreenspecs wbdg org 11 02 05 07900 2 Joint Sealants Whole Building Design Guide Federal Green Construction Guide for Specifiers B Backer Rods Provide composite backer rods PART 3 EXECUTION 3 X SITE ENVIRONMENTAL PROCEDURES A Indoor Air Quality 1 Temporary ventilation Provide temporary ventilation during work of this Section a Coordinate interior application of joint sealants with interior finishes schedule END OF SECTION http fedgreenspecs wbdg org 11 02 05 07900 3 Joint Sealants
View Full Document
Unlocking...