PowerPoint PresentationSlide 2Slide 3Slide 4Slide 5Slide 6Slide 7Slide 8Slide 9Slide 10Slide 11Slide 12Slide 13Slide 14Slide 151Lecture 15: DRAM Main Memory Systems• Today: DRAM basics and innovations (Section 2.3)2Memory ArchitectureProcessorMemory ControllerAddress/CmdDataDIMMBankRow Buffer• DIMM: a PCB with DRAM chips on the back and front• Rank: a collection of DRAM chips that work together to respond to a request and keep the data bus full• A 64-bit data bus will need 8 x8 DRAM chips or 4 x16 DRAM chips or..• Bank: a subset of a rank that is busy during one request• Row buffer: the last row (say, 8 KB) read from a bank, acts like a cache3DRAM Array Access16Mb DRAM array = 4096 x 4096 array of bits12 row address bitsarrive firstColumn decoder12 column address bitsarrive nextSome bits returned to CPU4096 bitsare read outRow Access Strobe (RAS)Column Access Strobe (CAS) Row Buffer4Organizing a Rank• DIMM, rank, bank, array form a hierarchy in the storage organization• Because of electrical constraints, only a few DIMMs can be attached to a bus• One DIMM can have 1-4 ranks• For energy efficiency, use wide-output DRAM chips – better to activate only 4 x16 chips per request than 16 x4 chips• For high capacity, use narrow-output DRAM chips – since the ranks on a channel are limited, capacity per rank is boosted by having 16 x4 2Gb chips than 4 x16 2Gb chips5Organizing Banks and Arrays• A rank is split into many banks (4-16) to boost parallelism within a rank• Ranks and banks offer memory-level parallelism• A bank is made up of multiple arrays (subarrays, tiles, mats)• To maximize density, arrays within a bank are made large rows are wide row buffers are wide (8KB read for a 64B request, called overfetch)• Each array provides a single bit to the output pin in a cycle (for high density)6Row Buffers• Each bank has a single row buffer• Row buffers act as a cache within DRAM Row buffer hit: ~20 ns access time (must only move data from row buffer to pins) Empty row buffer access: ~40 ns (must first read arrays, then move data from row buffer to pins) Row buffer conflict: ~60 ns (must first precharge the bitlines, then read new row, then move data to pins) • In addition, must wait in the queue (tens of nano-seconds) and incur address/cmd/data transfer delays (~10 ns)7Reads and Writes• A single bus is used for reads and writes• The bus direction must be reversed when switching between reads and writes; this takes time and leads to bus idling • Hence, writes are performed in bursts; a write buffer stores pending writes until a high water mark is reached• Writes are drained until a low water mark is reached8Open/Closed Page Policies• If an access stream has locality, a row buffer is kept openRow buffer hits are cheap (open-page policy)Row buffer miss is a bank conflict and expensive because precharge is on the critical path• If an access stream has little locality, bitlines are precharged immediately after access (close-page policy)Nearly every access is a row buffer missThe precharge is usually not on the critical path•Modern memory controller policies lie somewhere between these two extremes (usually proprietary)9Address Mapping Policies• Consecutive cache lines can be placed in the same row to boost row buffer hit rates• Consecutive cache lines can be placed in different ranks to boost parallelism• Example address mapping policies: row:rank:bank:channel:column:blkoffset row:column:rank:bank:channel:blkoffset10Scheduling Policies• FCFS: Issue the first read or write in the queue that is ready for issue• First Ready - FCFS: First issue row buffer hits if you can • Stall Time Fair: First issue row buffer hits, unless other threads are being neglected11Refresh• Every DRAM cell must be refreshed within a 64 ms window• A row read/write automatically refreshes the row • Every refresh command performs refresh on a number of rows, the memory system is unavailable during that time • A refresh command is issued by the memory controller once every 7.8us on average12Error Correction• For every 64-bit word, can add an 8-bit code that can detect two errors and correct one error; referred to as SECDED – single error correct double error detect•A rank is now made up of 9 x8 chips, instead of 8 x8 chips•Stronger forms of error protection exist: a system is chipkill correct if it can handle an entire DRAM chip failure13Modern Memory SystemPROC................• 4 DDR3 channels• 64-bit data channels• 800 MHz channels• 1-2 DIMMs/channel• 1-4 ranks/channel14Cutting-Edge SystemsPROCSMB........• The link into the processor is narrow and high frequency• The Scalable Memory Buffer chip is a “router” that connects to multiple DDR3 channels (wide and slow)• Boosts processor pin bandwidth and memory capacity• More expensive, high power15Title•
View Full Document
Unlocking...