CSCI 4550/8556 Computer NetworksLong-Distance CommunicationSending Signals Long DistancesOscillating SignalsEncoding Data With A CarrierTypes Of ModulationExamples of Modulation TechniquesSlide 8Encoding Data With Phase Shift ModulationHardware For Data TransmissionFull Duplex CommunicationExternal Modem ExamplesRack-Mounted Modem ExampleOther Types of ModemsLeased Serial Data CircuitsOptical, Radio and Dialup ModemsDialup ModemsOperation Of Dialup ModemsCarrier Frequencies and MultiplexingMultiplexingSpread Spectrum MultiplexingTime Division MultiplexingSummaryCSCI 4550/8556Computer NetworksComer, Chapter 6:Long Distance Communication(Carriers, Modulation, And Modems)Long-Distance Communication The encoding used by RS-232 cannot work in all situations Over long distances Using existing systems like telephone Different encoding strategies are neededSending Signals Long Distances Electric current becomes weaker as it travels on wires because wires have non-zero resistance. The resulting signal loss may prevent accurate decoding of data.Thus, this signal loss prevents the use of RS-232 over long distances.Oscillating Signals A continuous, oscillating signal will propagate farther than a non-oscillating signal (like those used in RS-232).Long distance communication uses such a signal, called a carrier.The waveform for a carrier looks like this: A carrier can be detected over much longer distances than RS-232 signal.Encoding Data With A Carrier Modifications to the basic carrier encode data for transmission.The technique used is called modulation.The same idea is used in radio and television transmission.Carrier modulation is used with all types of media - copper, fiber, radio, infrared, and laser.Types Of Modulation Amplitude modulation – the strength, or amplitude of the carrier is modulated to encode data.Frequency modulation – the frequency of the carrier is modulated to encode data.Phase shift modulation - changes in timing, or phase shifts encode data.Examples of Modulation Techniques Amplitude modulationExamples of Modulation Techniques Phase shift modulationEncoding Data With Phase Shift Modulation The amount of phase shift can be precisely measured. The measurement show how much of the sine wave is “skipped”The previous example shows 1/2 and 3/4 cycle Each phase shift can be used to carry more than one bit; for example, four possible phase shifts encode 2 bits: 00 - no shift 01 - 1/4 phase shift 10 - 1/2 phase shift11 - 3/4 phase shiftThus, each possible phase shift carries 2 bits.The data rate is twice the baud rate.Hardware For Data Transmission A modulator encodes data bits as a modulated carrier.A demodulator decodes bits from carrier.Data transmission requires a modulator at the source and a demodulator at the destination.Note that modulator and demodulator are generic terms. Other terms may be used to describe equipment that is primarily performing modulation and/or demodulation.Full Duplex Communication Most systems provide for simultaneous bidirectional, or full duplex, transmission. This requires a modulator and demodulator at each end:Long-distance connection is called a 4-wire circuit. A modulator and demodulator in a single device is typically called a modem (modulator/demodulator)External Modem ExamplesRack-Mounted Modem ExampleOther Types of Modems ISDN ModemCable Modem FrontRear Leased Serial Data Circuits Organizations often include 4-wire circuits in a network. Within a site - on a campus – an organization can install its own 4-wire circuits. Telephone companies supply off-campus wires. Telephone cables have extra wires (circuits) for expansion. Telephone company leases right to use wires to organization. Organization uses modems for data transfer. These are called serial data circuits or serial lines They operate in parallel with (but not connected to) existing telephone circuits.Optical, Radio and Dialup Modems Modems can be used with other media in addition to dedicated data circuits. Special forms of encoding/decoding transducers that use modulation for data encoding: Glass - data encoded as modulated light beam Radio - data encoded as modulated radio signal Dialup - data encoded as modulated sound A dialup modem connects to an ordinary phone line:Dialup Modems Dialup modems include circuitry for sending data.They also include circuitry to mimic telephone operation:Lifting handset Dialing Replacing handset (hanging up) Detecting dial tone They use full duplex on one voice channel:Different carrier frequencies used for each direction.Filters eliminate interference.Operation Of Dialup Modems The receiving modem waits for a call in answer mode.The other modem, in call mode:Simulates lifting the handset Listens for a dial tone Sends tones (or pulses) to dial number The answering modem: Detects the ringing Simulates lifting the handset Sends the carrier Calling modem: Sends the (other) carrier Data is then exchanged.Carrier Frequencies and Multiplexing Multiple signals with data can be carried on the same medium without interference.This allows multiple simultaneous data streams.For example, dialup modems can carry full-duplex data on one voice channel.Example - multiple TV stations in the “air” medium Each separate signal is called a channel.Multiplexing Carrying multiple signals on one medium is called multiplexing.Frequency division multiplexing (FDM) achieves multiplexing by using different carrier frequencies Receiver can "tune" to specific frequency and extract modulation for that one channel Frequencies must be separated to avoid interference. Only useful in media that can carry multiple signals with different frequencies – a high-bandwidth required.Spread Spectrum Multiplexing Spread spectrum uses multiple carriers. A single data stream is divided up and sent across different carriers. This can be used to bypass interference or avoid wiretapping,Time Division Multiplexing Time division multiplexing (TDM) uses a single carrier and sends data streams sequentially, each using the channel for a part of the time.Transmitter/receiver pairs share the single channel.TDM is the basis for most computer networks that use shared media; details will be covered later.Summary Long-distance communications use carriers and modulation for reliable communication. A modulator encodes data and a demodulator decodes data.Modulation can use changes in carrier amplitude, frequency or phase shift to encode data. Multiple transmitter/receiver pairs can