Cite as: Ron Roscoe, course materials for 6.101 Introductory Analog Electronics Laboratory, Spring 2007. MIT OpenCourseWare (http://ocw.mit.edu/), Massachusetts Institute of Technology. Downloaded on [DD Month YYYY]. DEPARTMENT OF ELECTRICAL ENGINEERING AND COMPUTER SCIENCE MASSACHUSETTS INSTITUTE OF TECHNOLOGY CAMBRIDGE, MASSACHUSETTS 02139 Spring Term 2007 Quiz 1 6.101 Introductory Analog Electronics Laboratory NOTE: USE CLOSEST 5% TOLERANCE RESISTOR VALUES FOR ALL RESISTORS. NOTE: SHOW ALL CALCULATIONS FOR ALL ANSWERS BUT THE MOST OBVIOUS! [If you want credit for work based on wrong answers!] Please look through the whole quiz before beginning. There are lots of questions, but most of them are very easy. Some even involve just copying information given right here in the quiz! It’s always good test-taking procedure to look over the whole quiz before deciding where to start, and so you can plan your time. Each question is worth 2 points, except for problem 3, where each question is worth 5 points. Problem 1: / 24 Problem 2: / 16 Problem 3: / 15 Problem 4: / 22 Problem 5: / 24 Total: /101 Grade in %: Name: Date:C=1000 pF; L = 100 μH; R= 10 Ω CRL ⎥⎦⎤⎢⎣⎡ω−ω+=C1LjRZ 1a. For the series circuit above, what kind of source should be used to drive it? 1b. Draw such a source on the schematic above and label it. 1c. What kind of response do we expect from this type of circuit; i.e. what will change as we vary the frequency of the source from below resonance through resonance to above resonance? 1d. Under what conditions will the impedance expression above be at a minimum? [Use math symbols, not numbers, to answer this!] 1e. Write an expression for the current in this circuit using Ohm’s law and the impedance expression above. 1f. What are Ohm’s first and middle names? 1g. Under what conditions will the expression you wrote in 1e above be a maximum? [Use math, not numbers.] 1h. Under what conditions will the expression you wrote in 1e above be 3 dB down from the maximum in 1g? [Math] 1i. What is the resonant frequency of the circuit above? [in Hz, not radians] 1j. What is the bandwidth of the circuit above? [Hz] 1k. What are the upper and lower –3dB frequencies for this circuit? [Hz] 1l. What is the “Q” of this resonant circuit? Cite as: Ron Roscoe, course materials for 6.101 Introductory Analog Electronics Laboratory, Spring 2007. MIT OpenCourseWare (http://ocw.mit.edu/), Massachusetts Institute of Technology. Downloaded on [DD Month YYYY].Cite as: Ron Roscoe, course materials for 6.101 Introductory Analog Electronics Laboratory, Spring 2007. MIT OpenCourseWare (http://ocw.mit.edu/), Massachusetts Institute of Technology. Downloaded on [DD Month YYYY]. 2a. Draw a schematic for a full-wave rectifier using two real diodes with a VF = 0.7 volt, a power transformer whose primary is designed for 120 V RMS 60 Hz input and whose secondary is designed to put out 18 VCT under any load conditions [zero source resistance]. Use a 1000 μF polarized electrolytic filter capacitor on the output, in parallel with a load resistor of value RL. 2b. To what value of voltage will the capacitor charge when there is no load current? 2c. How much load current can we draw from this power supply [through RL] without exceeding an output ripple current of 1 volt peak-to-peak? 2d. What is the average value of the DC output voltage of this power supply when the current in 2c is being drawn from the supply? 2e. What should be the voltage rating of the electrolytic capacitor? 2f. Now remove the load resistor and substitute a Zener regulator with a series current-limiting resistor and a 6.2 Volt Zener diode with a 5Ω dynamic internal resistance to ground. Choose a series resistor that is large enough to limit the output current to the value you found in question 2c. Draw a schematic below. In your schematic, replace the transformers, diodes, and filter capacitor with a DC voltage source in series with a ripple source [AC] and the series current limiting resistor; and use these to drive the Zener. Replace the Zener with a DC source in series with the Zener’s 5Ω dynamic impedance. 2g. What is the value of the series current limiting resistor? 2h. Assuming that the load current plus the Zener current equals the value you found in 2c, and using your schematic from 2f, calculate the value of ripple voltage that will appear across the load.NOTE: Each question for problem 3 is worth 5 points. 100 ΩD1D2D3D4RC+ 50 V DCVOUTVIN = 100 mV,1000 HzC 3a. In the figure above, assume that each diode has a VF of 0.6 volts. If R is adjusted to 47.6 kΩ, then what is the small-signal [incremental] diode resistance for each diode? [The temperature is 25o C.] 3b. Assuming that the reactance of both capacitors is 0 Ω at 1000 Hz, then what will be the AC output voltage of this circuit? 3c. What value will the rheostat have to be if we want to reduce the output voltage to 20 mV? Cite as: Ron Roscoe, course materials for 6.101 Introductory Analog Electronics Laboratory, Spring 2007. MIT OpenCourseWare (http://ocw.mit.edu/), Massachusetts Institute of Technology. Downloaded on [DD Month YYYY].RER2+20VR 1+Vin-+Vout-2N390410 mA+C1 4a. What is the configuration of the transistor amplifier above? 4b. Given that βF = 200 and βo = 150, what is the DC base current IB of the transistor? 4c. What value is required for RE to make VRE = VCE? 4d. If the current through R2 is 100 μA, what is the value required for R1, assuming that VBE = 0.7 V? 4e. What is the value of R2 ? 4f. What is the input impedance to this transistor amplifier, ignoring the effects of R1 and R2? 4g. Now find the input impedance including the effects of R1 and R2. 4h. What value of C is required for a –3dB point at 10 Hz? 4i. What is the output impedance of this amplifier? 4j. What is the approximate voltage gain of this amplifier? 4k. Draw the load line for this amplifier on the transistor output characteristics on the next page. Label the value of the quiescent base current curve, IB, and mark the Q-point. Cite as: Ron Roscoe, course materials for 6.101