WCU ECGR 2252 - ECGR 2252 Mini-Project 5 (2 pages)

Previewing page 1 of 2 page document View the full content.
View Full Document

ECGR 2252 Mini-Project 5



Previewing page 1 of actual document.

View the full content.
View Full Document
View Full Document

ECGR 2252 Mini-Project 5

48 views


Pages:
2
School:
Western Carolina University
Course:
Ecgr 2252 - Electrical Engineering Design I
Unformatted text preview:

ECGR 2 25 2 El ec t rica l E ng i n e er i ng D e si gn I De pa r tm e n t of El ec t ric a l C om pu t e r E ng in e e ri n g UN C Cha rl o tt e S p ri ng 201 0 Mini Project 5 10 points Due 11 00am on May 4 2010 Design of a Sound Ultrasound Activated Toggle Switch Consider the band pass filter BPF and voltage amplifier shown below which is designed by cascading low pass and high pass filters LPF HPF 1 Perform an AC Analysis from 100Hz to 1MHz using OrCAD and a decade sweep Plot the magnitude of the overall transfer function U1B OUT Vmic and label the center frequency point on this plot with its coordinates 2 Replace the ac source labeled Vmic with an electret microphone and build this design in the lab Pull up the electret mic with a 2 2K resistor Connect the output of this BPF voltage amplifier to the input of a properly designed FVC toggle circuit Refer to Mini project 3 Whistle into the mic and make sure the load toggles on and off use a visible LED as the load Modify this design in the lab as needed for tuning it to the input signal you plan to use in your final product R10 U1B8 R7 10k Vs 5Vdc 5 R9 U2A8 3 R8 10k C7 1u OUT 2 0 C1 C3 10k R1 LM358 V R2 0 R3 1 OUT 6 0 01u 4 V V 1k V 10k 4 7 V LM358 0 R4 10k 50mVac 0 01u 1k 10k C4 C2 1Vdc Vmic 330p 330p 0 Team leaders please submit your team s report that includes the following in the order shown a The plot obtained in Part 1 Write down the values of the center frequency and the overall gain at the center frequency 2 pts b Design calculations for R1 and C1 of the FVC circuit 2 pt c The schematic of your design including the FVC and load circuit that includes all the details and shows the actual part numbers passive component values including tolerances used in the lab 3 pts d A sheet signed by Dr Miri Dr Yanik or designees as the verification that your design has worked in the lab for the designed sequence and defined motion 3 pts Submission Your report must be typed using a word processing software The first page should include ECGR2252 Electrical Engineeri ng Design I Spri ng 2010 Mini project 5 Design of a Sound Ultrasound Activated Toggle Switch Team Names BSEE BSCpE or both effort Turn in hardcopies of your report in class on May 4 Also upload an electronic copy of your report into the assignment dropbox in Blackboard before 11 00am on May 4 Submit this as a single PDF file named Team number MP5 Submission Policy Late submissions will be accepted up to 5 business days but 10 will be deducted for each day that a submission is late Lateness policy applies to electronic submissions as well All electronic submissions with a time stamp that is later than 11 00am of the due date will be considered late 50 will be deducted for any submission that is not organized according to the numbering a through d above Hardcopy of each team s report is to be submitted by the team leader Individual grades will be assigned based on percent effort as judged by the team leader A grade of 0 will be assigned to any team member whose name is not written on the first page by the team leader


View Full Document

Access the best Study Guides, Lecture Notes and Practice Exams

Loading Unlocking...
Login

Join to view ECGR 2252 Mini-Project 5 and access 3M+ class-specific study document.

or
We will never post anything without your permission.
Don't have an account?
Sign Up

Join to view ECGR 2252 Mini-Project 5 and access 3M+ class-specific study document.

or

By creating an account you agree to our Privacy Policy and Terms Of Use

Already a member?