1CE 321 INTRODUCTION TO FLUID MECHANICS Fall 2009 LABORATORY 3: THE BERNOULLI EQUATION OBJECTIVES  To investigate the validity of Bernoulli's Equation as applied to the flow of water in a tapering horizontal tube to determine if the total pressure head remains constant along the length of the tube as the equation predicts.  To determine if the variations in static pressure head along the length of the tube can be predicted with Bernoulli’s equation APPROACH Establish a constant flow rate (Q) through the tube and measure it. Use a pitot probe and static probe to measure the total pressure head hTm and static pressure head hSm at six locations along the length of the tube. The values of hTm will show if total pressure head remains constant along the length of the tube as required by the Bernoulli Equation. Using the flow rate and cross sectional area of the tube, calculate the velocity head hVc at each location. Use Bernoulli’s Equation, hTm and hVc to predict the variations in static pressure head hSt expected along the tube. Compare the calculated and measured values of static pressure head to determine if the variations in fluid pressure along the length of the tube can be predicted with Bernoulli’s Equation. EQUIPMENT Hydraulic bench with Bernoulli apparatus, stop watch THEORY Considering flow at any two positions on the central streamline of the tube (Fig. 1), Bernoulli's equation may be written as 2222112122zpgVzpgV++=++γγ (1)2Bernoulli’s equation indicates that the sum of the velocity head (V2/2g), pressure head (p/γ), and elevation (z) are constant along the central streamline. As explained in the Appendix 1, Eq. 1 can be simplified for this apparatus. The tube is horizontal so z1=z2, and the pressure heads h1= p1/γ and h2 = p2/γ can be measured from a common arbitrary datum so that Bernoulli’s Equation simplifies to 22212122hgVhgV+=+ (2) Note that the sum on either side of the equal sign is the total pressure head hT. If Bernoulli’s Eq. is correct, the total pressure head (hT)has the same value at all locations on the central streamline. This is not obvious since the narrowing tube causes the velocity to vary along the length of the tube. For Bernoulli’s Eq. to be true the pressure head must decrease as much as the velocity head increases in moving from point 1 to point 2. The pitot probe you will use measures the total pressure head hT of the fluid a short distance upstream of the probe’s tip. The probe’s tip must be positioned about 3mm downstream from point where the measurement is desired and oriented so that it opens directly into the flow (Fig.1).3 Fig.1. Test section and manometer tubes The piezometers installed along the side of the tube measure static pressure head hSm. PROCEDURE A. Familiarize yourself with the apparatus. B. Level the apparatus. C. Carefully fill the manometer tubes with water to flush all air pockets from the system and ensure all connecting pipes are free of air. With the pump on and the flow control valve closed, the top of the water columns in the manometer tubes should all be at the same elevation. For best results, this level should be set at approximately 150 mm. To lower the levels, attach the hand pump to the inlet valve and increase the air pressure (poa) in the chamber at the top of the manometer tubes. To raise the levels, lower poa by releasing air at the inlet valve.4D. Make sure that all of the manometer tubes have their zero readings at the same elevation. If not, get help from your TA. E. The pitot probe can be positioned by loosening the gland nut and carefully moving the probe to the desired position. Before a reading is taken, the gland nut should be re-tightened by hand. F. Carefully adjust the bench supply control valve and the Bernoulli apparatus flow control valve to provide the combination of flow rate and system pressure (poa) which will give the largest convenient difference between the highest and lowest manometer levels. G. For a given valve setting (flow rate), do the following: 1. Measure volume and time so that you can determine flow rate. 2. With the pitot probe removed entirely from the tube’s test section, 3. Record each piezometer’s manometer reading. This is hSm. 4. Move the tip of the pitot probe to a position about 3mm downstream of each piezometer tap and record the reading of the pitot probe manometer at each location. This is hTm. 5. Repeat your measurements of volume and time to show that the flow rate has remained constant while you were making your measurements. 6. Repeat steps 1 to 4 for each of the three flow rates. 7. When finished, drain the apparatus. Make sure the pitot probe is completely inserted into the tube and the gland nut is tightened before leaving.5ANALYSIS A. Determine the three flow rates. • Use the volume-time data. B. Calculate the velocity head hvc (gVa2/2) at each cross section. • Use each flow rate and the six cross-sectional areas of the tube to determine the average fluid velocity (Va=Q/A) at each measurement position along the length of the tube. The tube diameters at measurement sections are in Fig.3 Appendix2 C. Calculate the best estimate of the true value of hT in the tube. • Use the value of hTm at point A in the converging section. D. Predict the variation of static pressure head hSt along the length of the tube. • Use Bernoulli’s Equation to predict hSt. • Use the measured values of total pressure head hTm. • Use the calculated values of velocity head hVc. E. Graph the values as a function of position along the tube. • Make one graph for each flow rate. • Make each graph the same size. • Use identical scales on all three graphs. • Show the measured values of total pressure head hTm, static pressure head hSm, and calculated values of velocity head hVc on each graph. • Show the theoretical variation of hT. • Label the graphs so that the different heads are clearly identifiable. F. Consider what the measurements show happened in the converging section of the tube. • Look at the graphs and tables.6•