DOC PREVIEW
UK EE 221 - Passive Filters, low-Pass and Band-Pass l fi ters

This preview shows page 1-2 out of 7 pages.

Save
View full document
View full document
Premium Document
Do you want full access? Go Premium and unlock all 7 pages.
Access to all documents
Download any document
Ad free experience
View full document
Premium Document
Do you want full access? Go Premium and unlock all 7 pages.
Access to all documents
Download any document
Ad free experience
Premium Document
Do you want full access? Go Premium and unlock all 7 pages.
Access to all documents
Download any document
Ad free experience

Unformatted text preview:

Ci it IICircuits IIEE221EE221Unit 5Instructor: Kevin D DonohueInstructor: Kevin D. DonohuePassive Filters, low-Pass and Band-Pass lfiltersFiltersFilters A filter is a circuit/system designed with ifi ti f it lit d d h specifications for its amplitude and phase frequency response. Since capacitors and inductors result in frequency dependent impedance elements, it is ibl t t i it th t filt t ( possible to create circuits that filter out (or pass) signal energies over specified frequency regions.gFilter Example:Filter Example: Find the transfer function for the circuit below and kth itd f th t f f ti D ib sketch magnitude of the transfer function. Describe the filtering properties of this circuit with inputvi(t) and output vo(t):po()-+vi(t)RRfC+vo(t)R1fo()- Show that this filter can be described as a low-pass filter. (i.e. as , then , and as 0, 0)(ˆjHfilter. (i.e. as , then , and as 0, then Gain at DC > 0).)(j()HjCapacitive and Inductive Elements:Capacitive and Inductive Elements: Consider the impedance magnitudes of the capacitor and inductor as a function of :Capacitor: Inductor: XCC1XLL For higher frequencies the capacitor impedance approaches short circuit behavior while the inductor impedance approaches open circuit behavior.circuit behavior. For lower frequencies the inductor impedance approaches short circuit behavior while the capacitor impedance approaches open circuit behavior.D ib th it i d t DCDescribe the capacitor impedance at DC.Describe the inductor impedance at DC.Basic Filter Types and Terminology  The most common types of filters are listed below: Low-pass High-passBand-passBandpass Band-reject (or notch) Filter Terms:Pbd f i t i l f i th t th h filt Passband-range of input signal frequencies that pass through filter relatively unimpeded. Stopband - range of input signal frequencies that are strongly attenuated (relative to the passband) in passing to the output. Ctff fth d f th b d/ t b d i F th Cut-off frequency -the end of the passband/stopband region. For the band-pass and band-reject filters there are 2 cut-off frequencies. 3 dB cut-off (or half power) frequency - the frequency where the magnitude of the transfer function is 3 dB down from its maximum valuevalue. Passive filter – filter circuit without amplifier elements (no external power). The gain for passive filters is always less than or equal to 1. Active filter – filter circuit using an amplifier element (i.e. an op amp). While the active filter requires p wer external t the input si nal it While the active filter requires power external to the input signal, it has greater flexibility for gain setting and superior buffering capabilities (i.e. filter properties do not change with the load).Band-Stop Filter Design Example: For the band-reject filter given below, determine the circuit parameters so that the center (anti-resonant) frequency is 15 kHz, and the bandwidth 1.5 kHz. Determine the resulting gain at gganti resonance, DC, and as .CLvi(t)vi(t)+vo(t)-R11 Show that  In general, if a second order band-reject filter can be put in canonical fLCBRCGG012121 () () DCgjpform:202202)()(ˆBsssGsHwhere G= gain at DC (GDC) = gain as  (G), B= 3 dB bandwidth, 0= center frequency. The gain at anti-resonance is 0.Canonical TF Forms for Basic Filters: For the 2ndorder band-pass22)(ˆooBssBsGsH For the 2ndorder band-reject2022020)()(ˆBsssGsH For the 1storder low-pass1)(ˆDCsGsH For the 1storder high-passcsGsH)(ˆgpwhere GDCis the gain at DC, G∞is the gain at infinity, and cis the 3 dB cs)(DCg,∞gy,c(half-power) cutoff frequency, and ois the resonant/center


View Full Document

UK EE 221 - Passive Filters, low-Pass and Band-Pass l fi ters

Documents in this Course
Filters

Filters

8 pages

Unit 12

Unit 12

13 pages

Load more
Download Passive Filters, low-Pass and Band-Pass l fi ters
Our administrator received your request to download this document. We will send you the file to your email shortly.
Loading Unlocking...
Login

Join to view Passive Filters, low-Pass and Band-Pass l fi ters and access 3M+ class-specific study document.

or
We will never post anything without your permission.
Don't have an account?
Sign Up

Join to view Passive Filters, low-Pass and Band-Pass l fi ters 2 2 and access 3M+ class-specific study document.

or

By creating an account you agree to our Privacy Policy and Terms Of Use

Already a member?