Drawing & Dimensioning GradingDimensioning features where points will be taken. First occurrence basis per report based on a perfect score of 10.Programming features where points will be taken. First occurrence basis per program based on a perfect score of 10.Drawing & Dimensioning GradingGuideline for grading Paperweight, and Yo-yo lab drawings.Dimensioning features where points will be taken. First occurrence basis per report based on a perfect score of 10.0.1 Point issues:1. Line thickness: dimensions, center lines, phantom lines, leaders, and arrows, to be finer than drawing lines2. Missing center lines3. Missing center points4. Missing arrows, unless ordinate dimensioning is used5. Both arrows point same way0.2 Point issues:6. Showing tangencies.7. Arrows pointing to radii at quadrants, or arrows do not point to or go through the center of the radius.8. Overlapping dimensions, arrows, or leaders. General clutter causing difficulty reading print.9. Not using an extra print when necessary to minimize clutter, or to clarify a detail.10. Double dimensioning11. Wrong way to show dimension, such as showing a diameter as a radius, or visa versa12. Having dimensions in parenthesis when you do not intend the dimension to be shown as a reference dimension13. Missing lines14. Dimensions within a view15. If using multiple sheets, not specifying there are other sheets, i.e. sheet 1 of 2, sheet 2 of 2, and so on16. Mixed, or wrong Angle Projections. In America we sweep (3rd angle projections), in Europe they roll (1st angle projections).17. Cross-sections not oriented, or displayed properly.18. Different size fonts.19. Dimensioning to tangencies.20. Extra dimensions that are not necessary.21. Wrong values.22. Wrong line type.23. Additional lines that should not appear.24. Hidden lines in cross-sections.0.5 Point issues:25. Missing dimensions26. Not showing whole part, except for the Lab I deliverable where the top view can be a separate drawing from the profile view. The Lab III requirement is to combine the views.27. Not specifying engraving depth and tool to use as a note.28. Design shows major geometry features that cannot be machined with tooling provided, such as groove depths designed deeper than the length of cut for the tool.29. Missing features for snap fit; draft where there should be straight wall engagement.30. Dimensions upside-down.2.008 Design & Manufacturing II Drawing & Program GradingPart Program GradingGuideline for grading Paperweight, and Yo-yo lab programs.Programming features where points will be taken. First occurrence basis per program based on a perfect score of 10.0.1 Point issues:1. Missing decimal points.(mill)2. Lowercase letters.(mill)3. Letter ‘O’, instead of number ‘0’ in ‘G’ words (mill)4. ‘Z’ feed cutting level in positive area (above part) (mill)0.2 Point issues:5. Facing with inappropriate tool. (mill, or lathe)6. Missing a G0 Z.1 at tool start-up. (mill)7. Missing G0 Z.1 before tool change. (mill)8. Missing an X, and Y movement at tool start-up. (mill)9. Rapid Z move on same block as X, and Y move. (mill)10. G1, and G2 on same block. (mill)11. Two ‘M” codes on same block (mill)12. 2 feeds on same block. (mill)13. Tool pick-up and X, Y move on same block. (mill)14. Turning backwards, (from chuck towards turret). (lathe)15. Using a trepanning tool where a larger tool would be more suitable for the operation. (lathe)16. Finish cuts at roughing feed rates. (lathe)17. Rapid move to Z.1 before positioning to in the X, and Y axes first, at tool start-up. (mill)18. Using wrong tool for trepanning. (lathe)19. Not including a feed when last tool used had a feed that is inappropriate for the new tool picked up. (mill)20. Missing a G90 on Z moves after being in G91 mode for the X, and Y moves.(mill)21. Missing ‘M26’, and ‘M30’ to end program (mill)22. Missing ‘R’ on G2, and G3 moves. (mill)23. Missing quadrant points on arc moves. (mill)24. ‘R’ on a line with no G2, or G3 when the intent was to go into circular mode from a G0, or a G1 mode. (mill)0.5 Point issues:25. Plunging too deep for selected tool. (mill, and lathe)26. Missing a Z retract before positioning to a new location. (mill)27. Missing a ‘G1’ on the Z move that goes back into the part after rapid positioning to a new location.(mill)28. Missing G2, or G3 when the intent was to go into circular mode after being in rapid, or feed mode.(mill)29. Not returning to a G1, or G0 after being in a G2, or G3 move when the intent was to go back to linear motion, or rapid motion, after being in circular motion.(mill)30. Turning OD to Z-.5. (lathe)31. Missing workshift designation G55, G56, or G57 after each tool pickup. (mill)32. Rapid move into part. (mill, and lathe)2.008 Design & Manufacturing II Drawing & Program Grading2.008 Design & Manufacturing II Drawing & Program