Product Design Property EstimationTypes of PropertiesVapor Pressure of MixtureDesign MethodsRefrigerant DesignSolubility Parameter PredictionFlory-Huggins solution theoryHansen Solubility ParameterGroup Contribution MethodsSlide 10Liquid Surface Tension/Wetting Group Contribution MethodParachor ValuesSelect Surfactants for DispersionGroup Contributions - HLBDrago E and CAcidsBasesWetting - Good MethodWetting –Fowkes (Drago) MethodTransport PropertiesDrug/Enzyme Target DevelopmentBio ConcentrationKinetic Parameter PredictionMany Desired Properties of a ProductMinimization ProblemOverviewProduct DesignProperty EstimationChapter 3Article on Phys. Property EstimationCHEN 4253Terry A. RingUniversity of UtahTypes of Properties•Thermodynamic Properties•Transport Proprieties•Kinetic PropertiesVapor Pressure of Mixture•VOC – Volatile organic content•Flash Calc with Process Simulator•Hand Calc.–Equation of State –Activity Coefficient Equation•Aspen/ProMax–Pick Thermo Package•Several are available–Polar liquids vs non-polar–Aqueous vs non-aqueous–High P vs low P•Input Components•Set up Flash unit with feed streams•Set Feed Stream composition•Run Calc –Vapor–Liquid–SolidDesign Methods•Physical Properties–Group Contributions–Thermo package in Process Simulator•Process Simulation of Refrigeration cycle–Condenser–Vaporizer–Pump–Valve to flash liquid to vaporRefrigerant Design•Large negative Joule-Thompson Coefficient•Large Enthalpy of Vaporization•High Liquid Heat Capacity•Low Pressure -Tboil below RT–Vapor Pressure > 1.4 Bar to assure no air leaks•High Pressure – Compressor/Condensor–Vapor Pressure < 14 Bar to keep compression ratio less than 10Solubility Parameter Prediction•Solubility Parameter–Solubility of liquid in liquid–Solubility of solid in liquid–Solubility of polymer in liquid•Group Contributions–Three parameters•Dispersive•Polar•Hydrogen BondingFlory-Huggins solution theory •The result obtained by Flory[1] and Huggins[2] is •The right-hand side is a function of the number of moles n1 and volume fraction φ1 of solvent (component 1 or a), the number of moles n2 and volume fraction φ2 of polymer (component 2 or b), with the introduction of a parameter chi, χ, to take account of the energy of interdispersing polymer and solvent molecules. •Molar volume of polymer segment•δ are Hildebrand solubility parameters, δ=√((ΔHvap-RT)/Vmolar)•δ=√(δd 2 + δp 2 + δh2), linkage to Hansen Solubility parametersHansen Solubility Parameter•Hansen Solubility Parameters were developed by Charles Hansen as a way of predicting if one material will dissolve in another and form a solution [1]. They are based on the idea that like dissolves like where one molecule is defined as being 'like' another if it bonds to itself in a similar way.•Specifically, each molecule is given three Hansen parameters, each generally measured in :• The energy from dispersion bonds between molecules • The energy from polar bonds between molecules • The energy from hydrogen bonds between molecules •These three parameters can be treated as co-ordinates for a point in three dimensions also known as the Hansen space. The nearer two molecules are in this three dimensional space, the more likely they are to dissolve into each other. To determine if the parameters of two molecules (usually a solvent and a polymer) are within range a value called interaction radius (R0) is given to the substance being dissolved. This value determines the radius of the sphere in Hansen space and it's center is the three Hansen parameters. To calculate the distance (Ra) between Hansen parameters in Hansen space the following formula is used:• •Combining this with the interaction radius gives the relative energy difference (RED) of the system:• •RED < 1 the molecules are alike and will dissolve •RED = 1 the system will partially dissolve •RED > 1 the system will not dissolve See Articles Solvents_Data.pdfGroup Contribution Methods•Group (bond) Contribution Methods–ni=number of groups of type i in polymer repeat unit or molecule–N= number of group types–Ai=group contribution to property p{n}–Mwi= Molecular weight of group I, sometimes another group contribution property–d=exponent for propertydNiiiNiiinMwnAnp11}{Group Contribution Methods•Polymer Glass Transition Temp.•Polymer Molar Volume•Polymer Density•Polymer Water Absorption–P. 66 of your bookLiquid Surface Tension/WettingGroup Contribution Method•Contact Angle – Young’s Equation•cos Θ = (γSV- γSL)/ γLV•Wetting when Θ => 0•Predicting Liquid surface tension•γLV=[ρLMw-1 Σ(NiPi)]4•Pi=Parachor Value of group–Surface tension in [dyne/cm]–Density [gm/cm^3]–Mw [gm/mole]•Liquid Mixtures surface tension based upon mole fraction, Xi•γLV= Σ γLV_iXiParachor ValuesTables from Ring, Fundamentals of Ceramic Powder Processing, Academci Press 1999.CH2=CH O CH3 Groups PiC 3 4.8H to C 6 17.1O to ether 1 20Double Bond 1 23.2γLV=[ρLMw-1 Σ(NiPi)]4Select Surfactants for Dispersion•Lower Surface tension of a liquid–Detergency•Hydrophilic-lipophilic Balance-HLB–HLB = 7+ ΣHi – ΣLi•Stabilized Suspension–HLBsurfactant= HLBparticleTables from Ring, Fundamentals of Ceramic Powder Processing, Academic Press 1999.Group Contributions - HLBTables from Ring, Fundamentals of Ceramic Powder Processing, Academic Press 1999.TiO2Drago E and C•Used to predict the Heat of mixing, ΔHAB–Acid (A) – Base (B) Interactions–Good for non-polar solvents–E = Electrostatic Contributions–C = Covalent ContributionsBABAABCCEEH AcidsBasesCan be predicted from Infrared or NMR peak shifts due to mixingSee Wettability By John C. BergWetting - Good Method•Work of Adhesion between to materials, WaAB= -(γSV-γSL) – γLVEnergy to replace solid-vapor and liquid-vapor interfaces with liquid-vapor interface.–Predicted byLiquidWetting –Fowkes (Drago) Method•Work of Adhesion–N = moles of interaction functional groups per unit area–f = factor to convert enthalpy to workTransport Properties•Molecular Dynamics Calculations–Intermolecular Forces•Lennard-Jones Potentials between Atoms–Location of Atoms in Molecule–Molecules Free to move–Monte Carlo Methods–Statistical Analysis•Molecular Structure Determined From Otimization•Drug