This study source was downloaded by 100000785469759 from CourseHero com on 09 27 2022 22 48 28 GMT 05 00 https www coursehero com file 39346986 6512 Lab Building a Switch and Router Network STUpdf 2017 Cisco and or its affiliates All rights reserved This document is Cisco Public Page 1 of 5 Lab Building a Switch and Router Network This lab has been updated for use on NETLAB Topology Addressing Table Device Interface IP Address Subnet Mask Default Gateway R1 G0 0 192 168 0 1 255 255 255 0 N A G0 1 192 168 1 1 255 255 255 0 N A PC A NIC 192 168 1 3 255 255 255 0 192 168 1 1 PC B NIC 192 168 0 3 255 255 255 0 192 168 0 1 Objectives Part 1 Configure Devices and Verify Connectivity Part 2 Display Device Information Background Scenario This is a comprehensive lab to review previously covered IOS commands In this lab you will configure the devices to match the addressing table After the configurations have been saved you will verify your configurations by testing for network connectivity After the devices have been configured and network connectivity has been verified you will use IOS commands to retrieve information from the devices to answer questions about your network equipment This lab provides minimal assistance with the actual commands necessary to configure the router Test your knowledge by trying to configure the devices without referring to the content or previous activities Note The routers used with CCNA hands on labs are Cisco 1941 Integrated Services Routers ISRs with Cisco IOS Release 15 2 4 M3 universalk9 image The switches used are Cisco Catalyst 2960s with Cisco IOS Release 15 0 2 lanbasek9 image Other routers switches and Cisco IOS versions can be used Depending on the model and Cisco IOS version the commands available and output produced might vary from what is shown in the labs Refer to the Router Interface Summary Table at the end of this lab for the correct interface identifiers Note Ensure that the routers and switches have been erased and have no startup configurations Consult with your instructor for the procedure to initialize and reload a router and switch This study source was downloaded by 100000785469759 from CourseHero com on 09 27 2022 22 48 28 GMT 05 00 https www coursehero com file 39346986 6512 Lab Building a Switch and Router Network STUpdf Lab Building a Switch and Router Network 2017 Cisco and or its affiliates All rights reserved This document is Cisco Public Page 2 of 5 Part 1 Configure Devices and Verify Connectivity Configure basic settings such as the interface IP addresses device access and passwords Refer to the This lab has been updated for use on NETLAB Topology and Addressing Table at the beginning of this lab for device names and address information Step 1 Assign static IP information to the PC interfaces a Configure the IP address subnet mask and default gateway settings on PC A b Configure the IP address subnet mask and default gateway settings on PC B c Ping PC B from a command prompt window on PC A Why were the pings not successful Step 2 Configure the router a Console into the router and enable privileged EXEC mode b Enter configuration mode c Assign a device name to the router d Disable DNS lookup to prevent the router from attempting to translate incorrectly entered commands as though they were host names e Assign class as the privileged EXEC encrypted password f Assign cisco as the console password and enable login g Assign cisco as the VTY password and enable login h Encrypt the clear text passwords i Create a banner that warns anyone accessing the device that unauthorized access is prohibited j Configure and activate both interfaces on the router k Configure an interface description for each interface indicating which device is connected to it l Save the running configuration to the startup configuration file m Set the clock on the router Note Use the question mark to help with the correct sequence of parameters needed to execute this command n Ping PC B from a command prompt window on PC A Were the pings successful Why The router has not been configuredThe pings were successful because the router was correctly configured This study source was downloaded by 100000785469759 from CourseHero com on 09 27 2022 22 48 28 GMT 05 00 https www coursehero com file 39346986 6512 Lab Building a Switch and Router Network STUpdf Lab Building a Switch and Router Network 2017 Cisco and or its affiliates All rights reserved This document is Cisco Public Page 3 of 5 Part 2 Display Device Information In Part 2 you will use show commands to retrieve information from the router and switch Step 3 Retrieve hardware and software information from the network devices a Use the show version command to answer the following questions about the router What is the name of the IOS image that the router is running How much DRAM memory does the router have How much NVRAM memory does the router have How much Flash memory does the router have b Use the show version command to answer the following questions about the switch What is the name of the IOS image that the switch is running How much dynamic random access memory DRAM does the switch have How much nonvolatile random access memory NVRAM does the switch have What is the model number of the switch Step 4 Display the routing table on the router Use the show ip route command on the router to answer the following questions What code is used in the routing table to indicate a directly connected network How many route entries are coded with a C code in the routing table What interface types are associated to the C coded routes 255k bytes250880k bytes512MB flash0 c2900 universalk9 mz SPA 151 4 M4 bin flash c3560 ipservicesk9 mz 122 55 SE8 c3560 ipservicesk9 mz 122 55 SE8 bin WS C3560V2 24PS512k bytes131072K of memoryC2G0 0 1 This study source was downloaded by 100000785469759 from CourseHero com on 09 27 2022 22 48 28 GMT 05 00 https www coursehero com file 39346986 6512 Lab Building a Switch and Router Network STUpdf Lab Building a Switch and Router Network 2017 Cisco and or its affiliates All rights reserved This document is Cisco Public Page 4 of 5 Step 5 Display interface information on the router Use the show interface g0 1 to answer the following questions What is the operational status of the G0 1 interface What is the Media Access Control MAC address of the G0 1 interface How is the Internet address displayed in this command Step 6 Display a summary list of the interfaces on the router and switch There