1Series and Parallel Circuits ECE 2100 Circuit Analysis Laboratory updated 16 May 2011 Pre-Laboratory Assignment 1. Consider the following series circuit. Derive a formula to calculate voltages V1, V2, V3 and V4 in terms of R1, R2, R3, R4, and VS. Figure 1. Series Circuit with Four Resistors 2. For the following circuit, derive a formula for R2 in terms of R1, V2, and VS. Figure 2. Series Circuit with Two Resistors23. Consider the following combination series/parallel circuit. Note that each of the nodes is numbered 0 (reference node or “ground”), 1, or 2. Figure 3. Combination Series/Parallel Circuit a. Derive a formula for the total resistance RT “seen by” VS in terms of R1, R2, and R3. b. Derive a formula for the current I1 in terms of R1, R2, R3, and VS. c. Use the current divider rule to find a formula for I2 in terms of I1, R2, and R3. d. Use the current divider rule to find a formula for I3 in terms of I1, R2, and R3. Procedures Part One 1. Consider the following resistor values for the circuit of Figure 1: R1 1000Ω (1kΩ) R2 2200Ω (2.2kΩ) R3 2700Ω (2.7kΩ) R4 4700Ω (4.7kΩ) Table 1. Resistor Values for Part One Complete a table with the nominal (column Nominal R) and actual (column Measured R) resistor values. Using the formulas derived in your pre-lab and the measured resistances (column Measured R), calculate the predicted voltages (column Calculated V) assuming a source voltage of VS=5V.32. Using the resistor values provided in Table 1, construct the circuit shown in Figure 1. Have your instructor check your work before energizing the circuit. 3. Energize your circuit and measure the voltages across each resistor. Record your findings, along with the voltages computed in step 1 (column Calculated V) in a table formatted as indicated. Compute the error percentage between the computed and experimental voltages. Nominal R Measured R Calculated V (using measured resistances) Measured V V % Error R1,V1 R2,V2 R3,V3 R4,V4 Part Two 4. Select a nominal 4.7kΩ resistor as R1. Carefully measure the value of this resistance. Select a second resistor from the resistor "grab bag" as R2. Using resistors R1 and R2, assemble the circuit of Figure 2. 5. Measure the voltage V2 across resistor R2. From this, along with the equation derived in the pre-lab, calculate the theoretical resistance R2. How do the theoretical and actual values compare? Part 3 6. Measure the values of three resistors with nominal values as indicated in Table 2. R1 2.2kΩ R2 2.7kΩ R3 4.7kΩ Table 2. Resistor Values for Part 3 7. Using the resistor values of Table 2 assemble the circuit of Figure 3 without the voltage source. Measure and record the total resistance RT “seen by” VS. Compare to the value of RT computed for the actual resistor values using the equation derived in the pre-lab. 8. Now connect a VS=5V voltage source (initially OFF of course). 9. Calculate the currents I1, I2 and I3 using your equation from the pre-lab. Tabulate your4results. 10. After your instructor checks your circuit, energize the circuit with VS=5V. Now measure the voltage drops across and currents through each resistor with polarities as indicated in Figure 3. Tabulate and calculate the current percent errors. Resistance R Calculated I Measured V % Error Current Nominal Measured Calculated (using measured resistances) Measured Calculated (using measured resistances) Measured R1 R2 R3 Part 4 11. A symbol for a rheostat or variable resistor is shown below. A rheostat works by varying the position of the “wiper” connected to terminal B. This position is often moved by turning a shaft. Notice that as the wiper position changes, the resistance from A to B and from B to C also changes, while the resistance from A to C remains the same. The resistances RAB and RBC can vary from 0 to RAC and are related by the equation .1=+ACBCACABRRRR 12. Obtain a rotating arm rheostat. Observe and measure the resistance between the terminals A-C and B-C as the shaft is rotated.513. Assemble the following circuit assuming a resistance ratio of 50%. Measure and record the voltages across A-C and B-C. Be sure to indicate the assumed polarity of measured voltages in your lab notebook. 14. Set the wiper to make the voltage drop across terminals B-C of the rheostat to be 1.5 V (label your assumed voltage polarity). Calculate what resistance between terminals B-C is required to obtain the 1.5V drop. Verify your answer by disassembling your circuit and measuring the resistance directly. Analysis Begin by reviewing the guidelines for keeping your lab notebook. Perform this analysis work in your lab notebook. 1. Be sure to calculate and comment on all percent errors computed in this lab (in appropriate sections of your notebook). 2. Does the data of Part 1 satisfy Kirchhoff's voltage law? Explain. 3. Does the data of Part 3 satisfy Kirchhoff's current law? Explain 4. Show from the data of Part 4 that the rheostat functions as a voltage divider. Credits and Copyright Adapted from material developed by current and former ECE faculty, including Professor Joseph Kelemen. © 2011 Damon A. Miller and Frank L. Severance. All rights