CSCI450 CISCO LAB 5 Page 1 of 4 1 15 2019 CSCI450 Fundamentals of Cisco Routing Purpose This lab is designed to give the student experience in Managing router IOS and configuration files Creating backups of the IOS and configuration files Resetting the privileged password once it has been lost Configuring a real router Using telnet to gather network information Trouble shooting tools Setting up host name resolution Before you attempt to configure the router you should read this lab thoroughly and document the commands and parameters you ll use Be sure to print and annotate you work often Complete the following with your assigned partner using the classroom Cisco 1000 router using Hyper terminal Document print you work 1 Reset the privileged password on the classroom router a Document the steps you followed to complete this step b Document your password 2 Set a hostname for this router 3 Set the time and date to the current date and time 4 Set the ip address for the Ethernet port to 192 168 5 235 24 5 Verify you configuration a What version of the IOS is running b Save your configuration 6 What is the storage capacity of the flash memory a What file s are stored in flash memory b How much memory is used c How much memory is available for use 7 Test connectivity to the instructors computer 192 168 5 5 a Were you successful Do not proceed until you have connectivity b If you did not have connectivity how did you fix the problem 8 Enable telnet on the classroom router CSCI450 CISCO LAB 5 Page 2 of 4 1 15 2019 a What did you do 9 Verify that you can access the classroom router via telnet a How did you do this 10 Save you configuration 11 Make a backup copy of your startup configuration on the instructor s computer Name your backup config xxx yyy config where the xxx and yyy are replaced by partner names Ie steve bill config Note Be sure the instructor computer is running a tftp server If not be sure you know how to start it The default tftp folder is c students cisco The administrator password for accessing instructor is cnapwd 12 Print the contents of the backup configuration file 13 Erase the start up configuration 14 Reset the router Do not enter setup mode a Reconfigure the Ethernet interface s ip address b Recover you configuration from you backup copy c What did you need to do this d How did you verify that it was recovered properly e Save your running config to NVRAM The reminder of this lab is to be completed individually on the simulator HostA1 is a tftp server From Boston 15 You need to upgrade your IOS The tftp server has the new version stored under the name c2500 js l 120 8 bin a What does the name of the IOS upgrade file tell you b What is the name of the IOS file for the version you are currently using c What version is the IOS d You need to backup your IOS before upgrading i What did you observe e Upgrade your IOS i What did you observe ii What version of the IOS are you now running From Hartford 16 Backup your configuration a What did you observe CSCI450 CISCO LAB 5 Page 3 of 4 1 15 2019 CSCI450 CISCO LAB 5 Page 4 of 4 1 15 2019 17 Set the Boston and Hartford router so no password is needed for Telnet From New York 18 Telnet to Boston and Hartford a What did you need to do to accomplish this b How many session do you have active i What did you do to accomplish this step ii What other information is available regarding these session s 19 Go to Hartford disconnect all telnet sessions a How was this accomplished 20 Close all telnet sessions 21 Build a hostname to ip address DNS table for all devices on your network 22 Verify you DNS table a How did you do this 23 From Hartford display cdp timer information a Record this information in your lab documentation 24 Change your timer time to 90 secs a Verify this worked properly 25 Gather CDP information for all your interfaces a Document this in you lab report 26 From Boston gather all the information you can about your directly connected neighbors a Document this in you lab report 27 From Boston gather cdp information for the devices directly connected to New York a How did you do this b Document you findings in your lab report
View Full Document
Unlocking...