506736-4001B Page 1 of 4 12502 Exchange Dr., Ste 440, Stafford, TX. 77477 T:281.494.4505, F:281.494.5310 www.spectrumdigital.com USB Cable System Hardware and Software Requirements These operating platform requirements are necessary to install the Code Composer Studio (CCS) Integrated Development Environment and support the USB port. The requirements for the operating platform are: Minimum Hardware Configuration • 233 Mhz. or faster Pentium or compatible • 600MB of free hard disk space • Microsoft Windows 98SE, 2000(SP1 or higher) or XP • 64MB of RAM • SVGA (640x480) color display • Local CD-ROM Drive • Recommended Hardware Configuration • 128MB of RAM • SVGA(1024 x 768) color display • 500 Mhz. or faster Pentium or compatible DSP Starter Kit (DSK) for the TMS320C6713Quick Start Installation GuideThe TMS320C6713 DSK contains: AC Power Cord +5V Universal Power Supply C6713 DSK Board TMS320C6713 DSK Technical ReferenceC6713 DSK Code Composer Studio CD ROM DSP Development Systems2002TMS320VC5416 DSKTechnicalReference506206-4001B Page 2 of 4 12502 Exchange Dr., Ste 440, Stafford, TX. 77477 T:281.494.4505, F:281.494.5310 www.spectrumdigital.com Installing the DSK Code Composer Studio for Windows 98SE/2000/XP Before you install the DSK software, make sure the PC has a USB port and an operating system (Windows 98SE/2000/XP) that supports USB. Note: For Windows 2000 and XP you must install Code Composer Studio using Administrator privileges. To run CCS on these systems requires write permission on the registry. If installing hardware, follow the instructions provided with the hardware. Also prior to installing the DSK Code Composer Studio make sure the Virus checker on your system is turned off or disabled. It may be turned on or enabled when running CCS. 1. Insert the Code Composer Studio installation CD into the CD-ROM Drive. An install screen should appear; if not, go to Windows Explorer and run setup.exe from the CD-ROM. 2. Choose one of the following install options: • Code Composer Studio. Full install of CCStudio for the C6713DSK. • C6713DSK Patch to CCStudio v2.20. Patch install to your existing version of CCStudio v2.20. Requires CCStudio v2.20. If you select this option then you must run Setup CCS 2 (C6000) and import the “TMS320C6713DSK –0x540” configuration. 3. Respond to the dialog boxes as the installation program runs. 4. Leave your Code Composer CD ROM in the CD-ROM drive as it will be needed during USB Hardware install. Restart your computer if prompted to by the CCS Install. The DSK CCS v2.2 will automatically configure your system with a preset configuration for the C6713 DSK USB device. The installation procedures will create two icons on your desktop: C6713 DSK Startup – C6713 DSK CCS C6713 DSK Diagnostics – 6713 DSK Diagnostic Utility Connecting the C6713 DSK to your PC 1. Connect the supplied USB cable to your PC or laptop. If you connect the USB cable to a USB Hub, be sure the hub is connected to the PC or laptop and power is applied to the hub. Note: Connecting through a USB Hub is a highly recommended procedure during development to protect your computer’s USB Port from damage. 2. If you plan to install a microphone, speaker, or expansion card these must be plugged in properly before you connect power to the DSK board. 3. Plug the AC power cord into the power supply and AC Source. Warning: Power Cable Must be plugged into AC Source Prior to Plugging the 5 Volt DC output Connector into the DSK. 4. Plug the power cable into the board. 5. When power is applied to the board the Power On Self Test (POST) will run. LEDs 0-3 will flash. When the POST is complete all LEDs blink on and off then stay on. At this point your DSK is functional and you can now finish the USB install. JumpersLEDsSwitchesUSB CablePower supplyUSB connector(Plugs into DSK)USB connector(Plugs into USBHub, or port onPC/Laptop)S1012301231234ONSW3 6. Make sure your CCS CD ROM is installed in your CD-ROM drive. Now connect the USB cable into the DSK. After few moments Windows will detect new hardware and prompt you with New Hardware Found screens. Follow the instructions on the screens and let Windows find the USB driver files “sdusbemu.inf” and “sdusbemu.sys” on your Code Composer CD-ROM. On XP systems Windows will find the drivers automatically.506206-4001B Page 3 of 4 12502 Exchange Dr., Ste 440, Stafford, TX. 77477 T:281.494.4505, F:281.494.5310 www.spectrumdigital.com Testing Your Connection If you want to test your DSK and USB connection you can launch the C6713 DSK Diagnostic Utility from the icon on your desktop. From the diagnostic utility, press the start button to run the diagnostics. In approximately 20 seconds all the on-screen test indicators should turn green. Starting Code Composer To start Code Composer Studio, double click the C6713 DSK CCS icon on your desktop. Running the Code Composer Tutorial The on-line help included with the C6713 DSK contains in-depth information about the hardware and software that comes with the kit. It also contains a tutorial that will help you get started with your DSK and learn about its features. To access the on-line help and run the tutorial, follow these steps: 1. Start Code Composer Studio (ignore this if CCS is already running) by double-clicking on the C6713 DSK icon on your desktop. 2. Open the CCS general help by selecting HelpÆContents in the CCS menu. 3. Expand the C6713 DSK specific help by expanding the help topic labeled TMS320C6713 DSK. It should be the last topic in the help topic list. 4. Look in the section entitled “Welcome to Your ‘C6713 DSK”. You will find the tutorial and other introductory material there. Code Composer Registration Remember to register your product within 30 days of purchase. Texas Instruments may make available DSK specific patches, utilities or promotions to