DOC PREVIEW
GVSU EGR 250 - Use of Hardness Testing in Determining Processing Conditions and Ductility of Metal Alloys

This preview shows page 1-2-3-4 out of 11 pages.

Save
View full document
View full document
Premium Document
Do you want full access? Go Premium and unlock all 11 pages.
Access to all documents
Download any document
Ad free experience
View full document
Premium Document
Do you want full access? Go Premium and unlock all 11 pages.
Access to all documents
Download any document
Ad free experience
View full document
Premium Document
Do you want full access? Go Premium and unlock all 11 pages.
Access to all documents
Download any document
Ad free experience
View full document
Premium Document
Do you want full access? Go Premium and unlock all 11 pages.
Access to all documents
Download any document
Ad free experience
Premium Document
Do you want full access? Go Premium and unlock all 11 pages.
Access to all documents
Download any document
Ad free experience

Unformatted text preview:

4 DiscussionUse of Hardness Testing in Determining Processing Conditions and Ductility of Metal Alloys by Brad Peirson School of Engineering Grand Valley State University Laboratory Module 4 EGR 250 – Materials Science and Engineering Section 1 Instructor: Dr. P.N. Anyalebechi June 14, 2005Abstract An experiment was run to measure the hardness of eleven metal samples. The identity of ten samples was known with the eleventh to be determined after the data had been examined. Ultimately it was determined that this sample closely resembled nodular cast iron. After the hardness data was assembled the average hardness of each sample was compared to both the calibration data for the hardness tester and to published hardness values. This comparison led to assumptions being made as to the processing conditions of each of the samples. After the processing conditions were determined the samples were ranked in order of increasing ductility. Finally a metal was chosen from the group for a wear resistant application based on this ranking. The hardest of the eleven samples, gray cast iron, was chosen for this application. 1 Introduction Hardness testing is a method by which the overall toughness of a material can be determined. There are several different scales that can be employed in hardness testing based on the material under examination. All of the different scales operate in the same manner. They also use the same equipment to obtain results. Hardness tests are performed on a hardness tester. The tester consists of an anvil that the specimen sits on during testing. An indenter is then pressed into the specimen. The type of indenter used, the weight used and the way the indentation is measured are the three ways that the proper hardness scale is determined. The Rockwell B scale uses a 0.1875 mm (1/16”) steel ball as the indenter with a mass of 100 kg. The other unique feature of the Rockwell B scale is the way in which the indentation is measured. A majority of the other hardness scales measure the diameter of the indentation in some manner whereas the Rockwell B scale measures the depth that the indenter penetrates the specimen [1]. The ductility of a specimen can be found based on the results of the hardness tests. Generally the harder a material is the less ductile it will be. Using this reasoning a 1set of materials can be ranked by their ductility. Hardness is also a key factor in determining the proper material for a given application. For example, an application that requires good wear resistance would require a hard material. Because hardness is related to the materials ability to resist surface deformations it can be directly associated with toughness. 2 Experimental Procedure Eleven metal samples were obtained form the instructor for the hardness tests. The type of metal in each sample is given in Table 1. Each sample was tested three separate times using the Rockwell B scale. This scale employs a 0.1875 mm (1/16”) steel ball with a load of 100 kg. Care was taken to insure that each test was conducted sufficiently far from indentations left by precious tests. Once the hardness values were gathered they were analyzed. The results are shown in Table 1. The gathered hardness values were compared to published values. This comparison is shown in Figure 2. The results of the comparison were used to infer their processing conditions and rank them according to their ductility. 3 Results The results of the statistical analysis are shown in Table 2. The standard deviations of the samples showed quite a bit of variation, as did the range. Some of the samples do approach the data for the calibration in Table 1. The average hardness for each of the eleven samples were all relatively close to the published values. No statistical analysis was performed on the difference between the average and published hardness values. The published hardness values shown in Table 3 were taken from metals with the same composition with different processing conditions. Once published values were found for each metal sample the compostion of each was found. The composition of each sample based on the published data is shown in 2Table 4. These compositions give the acceptable range of primary alloying elements. They also exclude impurities in the alloys. The probable processing conditions for each of the eleven samples are listed in Table 3. Under specific processing conditions published values were found that closely resembled those of the samples. From the similarities in hardness and given the consistent composition shown in Table 4 inferences were made based about the processing conditions of the eleven test samples. These inferences are contained in Section 4. Table 1: Results of Calibration Performed on Hardness Tester, 11 am 6-7-05 Calibration Results, RB 92.5 92.4 92.0 92.0 91.7 92.3 92.0 Standard: 91.2 ± 1.2 RB Standard Deviation: 0.28115Mean: 92.1Range: 0.8 In addition to the inferences made about the processing conditions, an estimate can be made as to the identity of the unknown sample of cast iron. The sample can be identified by comparing the hardness values recorded to published values for cast iron samples. 3Table 2: Statistical Analysis of Eleven Metal Samples Hardness, RB Metal 1 2 3 µ R σ AA2024 80.5 80.7 80.4 80.5 0.3 0.2 AA6061 51.2 49.9 49.1 50.1 2.1 1.1 Phosphor Bronze 76.9 79.4 79.9 78.7 3.0 1.6 Brass 65.8 69.8 72.5 69.4 6.7 3.4 C1018 98.2 100.5 97.3 98.7 3.2 1.7 ? Cast Iron 101.1 101.1 100.1 100.8 1.0 0.6 Ductile Cast Iron 95.5 96.0 95.9 95.8 0.5 0.3 Gray Cast Iron 101.7 102.5 101.0 101.7 1.5 0.8 Cu 38.6 37.0 40.7 38.8 3.7 1.9 Ti 82.6 85.5 84.9 84.3 2.9 1.5 Stainless Steel 88.2 95.3 89.6 91.0 7.1 3.8 0.020.040.060.080.0100.0120.01234567891011MetalHardness, RB Figure 1: Average Hardness Across 11 Metal Samples, Ordered as in Table 1 4Table 3: Average Hardness Values For Eleven Metal Samples with Published Hardness Values and Processing Conditions Published Metals µ, RB Hardness, RB Condition Source AA2024 80.5 80 T361 [2] AA6061 50.1 26 T451 [2] Phosphor Bronze 78.7 73 C50500-H06 [2] Brass 69.4 70 C27000-H02 [2] C1018 98.7 92 Carburized [2] ? Cast Iron 100.8 100 Nodular [2] Ductile Cast Iron 95.8 96 80-55-06 [2] Gray Cast Iron 101.7 100 Class 50 [2] Cu 38.8 40 C10100-H02 [2] Ti 84.3 80 Grade 4 [3] Stainless Steel 91.0 88 18 CR-CB [2]


View Full Document

GVSU EGR 250 - Use of Hardness Testing in Determining Processing Conditions and Ductility of Metal Alloys

Download Use of Hardness Testing in Determining Processing Conditions and Ductility of Metal Alloys
Our administrator received your request to download this document. We will send you the file to your email shortly.
Loading Unlocking...
Login

Join to view Use of Hardness Testing in Determining Processing Conditions and Ductility of Metal Alloys and access 3M+ class-specific study document.

or
We will never post anything without your permission.
Don't have an account?
Sign Up

Join to view Use of Hardness Testing in Determining Processing Conditions and Ductility of Metal Alloys 2 2 and access 3M+ class-specific study document.

or

By creating an account you agree to our Privacy Policy and Terms Of Use

Already a member?