DOC PREVIEW
Rose-Hulman ECE 300 - System Step and Impulse Response

This preview shows page 1-2 out of 7 pages.

Save
View full document
View full document
Premium Document
Do you want full access? Go Premium and unlock all 7 pages.
Access to all documents
Download any document
Ad free experience
View full document
Premium Document
Do you want full access? Go Premium and unlock all 7 pages.
Access to all documents
Download any document
Ad free experience
Premium Document
Do you want full access? Go Premium and unlock all 7 pages.
Access to all documents
Download any document
Ad free experience

Unformatted text preview:

ROSE-HULMAN INSTITUTE OF TECHNOLOGY Department of Electrical and Computer Engineering ECE 300 Signals and Systems Fall 2008 System Step and Impulse Response Lab 04 Bruce A. Ferguson In this laboratory, you will investigate basic system behavior by determining the step and impulse response of a simple RC circuit. You will also determine the time constant of the circuit and determine its rise time, two common figures of merit (FOMs) for circuit building blocks. Objectives 1. Design an experiment by specifying a test setup, choosing circuit component values, and specifying test waveform details to investigate the step and impulse response. 2. Measure the step response of the circuit and determine the rise time, validating your theoretical calculations. 3. Measure the impulse response of the circuit and determine the time constant, validating your theoretical calculations. Prelab Find and bring a circuit board to the lab so you can build the RC circuit. Background As we introduce the study of systems, it will be good to keep the discussion well grounded in the circuit theory you have spent so much of your energy learning. An important problem in modern high speed digital and wideband analog systems is the response limitations of basic circuit elements in high speed integrated circuits. As simple as it may seem, the lowly RC lowpass filter accurately models many of the systems for which speed problems are so severe. There is a basic need to be able to characterize a circuit independent of its circuit design and layout in order to predict its behavior. Consider the now-overly-familiar RC lowpass filter shown in Figure 1. We could describe this system by showing its circuit schematic or by calculating its impulse response or transfer function. But in many cases only FOMs are important to determine the adequacy of the system. Page 1 of 1EC 300 Signals and Systems Fall 2008 Figure 1. Simple RC lowpass filter circuit. +C1Vout-+0+-V1+R1 The first FOM is the system time constant. Many simple systems display a characteristic exponential decay (or rise) in their response. Since the form of the response is known, the only data important to characterize a specific system is the numerical value of its time constant. The second FOM, the risetime, characterizes the response of the system to a positive step change in input. The response of the circuit of Figure 1 to an applied unit step input is shown in Figure 2. The rise time most typically used as a FOM for a first order system is the “10-90% risetime”, which is simply the amount of time necessary for the output to rise from 10% to 90% of its final value. This measurement in shown in Figure 2 as the time difference between the times t10 and t90. These values can easily be determined given the step response of the system. t90t10rise timetr= t90-t1090%10%t90t10rise timetr= t90-t1090%10% Figure 2. Step response of the RC lowpass filter circuit of Figure 1, showing the definition of the 10-90% risetime. The 10-90% risetime FOM is especially important in digital systems, as excessive “slurring” of the crisp edges of the digital waveform leads to rapid degradation in system performance. Page 2 of 2EC 300 Signals and Systems Fall 2008 The risetime is a slightly deceiving measurement for certain circuits, since the rise time depends in part on the magnitude of the step change in output the circuit must produce. For this reason, a related FOM, the slew rate, is required to describe the maximum voltage change per unit time which the circuit can produce. Figure 3 shows a typical impulse response for the RC filter of Figure 1. The characteristic exponential decay is just as we remember from class. The time constant of the circuit is defined as the time it takes for the response to decay to 1/e (37%) times its initial value. Since the functional form of the response is exp(-t/RC), the time constant of the circuit can easily be shown to be simply RC. 1/e*1=0.368τ = time constant1/e*1=0.368τ = time constant Figure 3. Impulse response of the RC lowpass filter circuit of Figure 1, showing the definition of the circuit time constant. The time constant FOM allows us to determine the behavior of the circuit in a number of important scenarios, such as digital signal response or the time until steady-state analysis results are valid. Measuring these two FOMs in the laboratory is actually a relatively simple effort for low bandwidth systems. The requirements are the circuit, or the system under test (CUT or SUT), and appropriate step and impulse waveform generation and measurement equipment. However, some thought needs to go into the waveform specification in order to facilitate measurement of the two FOMS. The basic test setup is shown in Figure 4. The trick is to be able to create a “ unit step” and an “impulse” waveform to test the system. Of course, we cannot create either of these two ideal waveforms in our part of the universe. However, we can create reasonable approximations. Page 3 of 3EC 300 Signals and Systems Fall 2008 functiongeneratorscopetriggertriggerCircuitFG outputinputfunctiongeneratorscopetriggertriggerCircuitFG outputinput Figure 4. Experimental test setup for measuring the impulse and step response of the SUT. How can we approximate a unit step impulse? There are three important aspects of the step waveform to consider. First, the waveform must have a fast transition from off to on. Second, the waveform must stay “on” long enough for the system transients to die out. Thus, we could imagine a suitably wide pulse as being a reasonable approximation to a step input. The third aspect has to do with how we create the step change in the waveform. To simulate the impulse waveform, we could use a suitably abrupt and high amplitude pulse waveform. But what constitutes “suitably abrupt”? Well, if we can produce a pulse whose time width is much less than the time constant of the circuit, with a suitably large amplitude, then the pulse would provide a reasonable approximation of an impulse for that circuit. That same pulse might not be short enough in duration to approximate an impulse for a different circuit having a shorter time constant. Each of the two waveforms discussed above are single-shot events, or events that occur only once in time. The oscilloscopes we use are optimized for periodic waveforms, not single-shot events. No worries


View Full Document

Rose-Hulman ECE 300 - System Step and Impulse Response

Documents in this Course
Exam 2

Exam 2

8 pages

Load more
Download System Step and Impulse Response
Our administrator received your request to download this document. We will send you the file to your email shortly.
Loading Unlocking...
Login

Join to view System Step and Impulse Response and access 3M+ class-specific study document.

or
We will never post anything without your permission.
Don't have an account?
Sign Up

Join to view System Step and Impulse Response 2 2 and access 3M+ class-specific study document.

or

By creating an account you agree to our Privacy Policy and Terms Of Use

Already a member?