Honors Cup Synthetic Proposal Section: 221 Group Members: Michelle (Yoon Young) Choi Yazhuo (Grace) Liu Beth Parker Shruti Saran Title: Synthesis of Vanillin from Catechol Introduction: Vanillin (4-hydroxy-3-methoxybenzaldehyde) is a synthetic compound used extensively as a flavoring agent in many foods like chocolate, ice cream, and baked goods. It is also used for its pleasant scent in perfumes and is a flavoring agent in beverages. A large amount of vanillin (about 40% of all synthesized) is used as a pharmaceutical intermediate as well. Vanillin is available from three different sources: the vanilla bean itself, from guaiacol, or from lignin. The following synthesis uses, as most of the chemical industry does, the guaiacol route. However, to be more cost efficient, we will synthesize guaiacol from catechol. Thus, the first step of the synthesis will be making guaiacol from catechol. Then, the guaiacol will be changed into vanillylmandelic acid (VMA). Finally, the VMA will be converted into vanillin. Target Molecule: Vanillin 4-hydroxy-3-methoxybenzaldehyde (C8H8O3) OHOCH3OOverall synthetic reaction scheme: OHOHOHOCH3OOHONaOH2) HClOCH3HOOOHOHBi(0) (10%)DMSO, O2 (1atm)AcOH, 125¨¬COHOCH3OMe2SO4 or(CH3)SO41)Step 1 Synthetic transformation 1: OHOHOHOCH3NaOH(CH3)2SO4 Experimental 1 Monomethylation of Catechol All reagents were obtained from commercial suppliers and used without further purification. 0.10 mol of catechol was added to a solution of NaOH (40%, 10 mL, 0.1 mol) and dissolved under heating. Water was evaporated under reduced pressure. Polyethylene glycol – PEG400 – (1.6 grams or about 0.04 mol) and .11 mol of dimethyl sulfate were added to the reaction system while vigorously stirring. The reaction was heated and monitored with TLC until the conversion of phenol was complete. Then, the mixture was poured into a hot NaOH solution (5%) or water (80-90 degrees Celsius, 100 mL) with stirring. The mixture was allowed to precipitate or separate into layers. The precipitate or organic layer was then washed with water (3x50mL). If a higher purity is desired, recrystallisation with a suitable solvent or distillation in vacuum may be used. Expected yield: 86% Safety, disposal and green issues 1: Safety Safety is a concern when dealing with many aromatic compounds, and catechol is no different. It is stable but care should be taken to limit exposure to air and light. It is a mutagen, tumorigen, and reproductive effector. It may also cause burns. It is harmful when inhaled, ingested, or absorbed by the skin. Dimethyl sulfate is a dangerous chemical. It is extremely toxic and carcinogenic as well as flammable. It is very important to wear goggles, gloves, cap the bottle, and keep it under a hood when dealing with these chemicals. Sodium hydroxide is very corrosive and should be used with care also. Disposal When disposed of, catechol should be separated from strong oxidants and kept in the dark. Ventilation is also suggested. Sodium hydroxide should be stored in a container with similar bases. Dimethyl sulfate should be in a dry, well-ventilated area with containers closed. It shouldalso be away from direct sunlight, heat, and not with strong oxidizers or alkalines. Discard waste materials based on the following categories unless otherwise indicated: acids, bases, halogenated, and non-halogenated. See federal, state, and local regulations for more information. Green Catechol is a relatively inexpensive chemical. It is about $0.33 per gram. NaOH is a substance already found in the lab, which costs around 10 cents a gram, depending on the type used. Dimethyl sulfate is inexpensive as well, at roughly 5 cents per milliliter. Step 2 Synthetic transformation 2: OHOCH3OOHO2) HClOCH3HOOOHOH1)NaOH Experimental 2 Electrophilic Substitution of Glyoxylic Acid on Guaiacol A solution of 176 g (4.4 mol) of NaOH in 100 mL of water (15 degrees Celsius) was combined with 1 kg of crushed ice. 250 g (2.014 mol) of guaiacol (our previous product) was added to this mixture, surrounded by an ice-salt bath, while stirring. While stirring, an ice-cold solution of 225 g (2.5 mol) of glyoxylic acid monohydrate in 400 mL of water was introduced dropwise during 4 hours. The reaction was kept at 0 to -5 degrees Celsius. A precipitate may form as an indicator of adding the glyoxylic acid too quickly but will disappear on stirring. The solution was stirred for an additional 20 hours while the temperature slowly returned about 20 degrees Celcius. 375 mL of concentrated hydrochloric acid was added to the dark-brown solution. This is then saturated with 700 g of salt and extracted with benzene (3x100mL). The benzene extract was dried with sodium sulfate. The aqueous layer was then extracted with ethyl acetate (15x250mL). The extracts were combined, dried again with sodium sulfate, treated with 3g of acid-washed charcoal. Then this mixture is concentrated into a syrup using the rotary evaporator. The syrup was cooled, and the product crystallized. This was filtered and washed with cold ethyl acetate to give almost colorless crystals.Expected yield: 40% Safety, disposal and green issues 2: Safety Guaiacol (the product of step 1) is not known to be extremely toxic, but may affect the central nervous system. It is hazardous with eye contact, ingestion, or inhalation. It is also slightly hazardous with skin contact as an irritant. It should be used only in a well-ventilated area. Glyoxylic acid is somewhat corrosive, so skin contact should be avoided, as with sodium hydroxide. Handle concentrated HCl and beneze with extreme care as HCl is corrosive and benzene is carcinogenic and flammable. Disposal Guaiacol should be kept in a cool, well-ventilated area. It should not be stored near oxidizing agents, acids, or bases. Glyoxylic acid should be kept around room temperature, but is relatively stable. Sodium hydroxide should be stored with other bases. Discard waste materials based on the following categories unless otherwise indicated: acids, bases, halogenated, and non-halogenated. See federal, state, and local regulations for more information. Green In this step, guaiacol has been synthesized, so we do not need to purchase it. NaOH has already been purchased, and H2O can be taken directly from the labs’ faucets. The only compound to be purchased for this step is glyoxylic acid. This is
View Full Document
Unlocking...