DOC PREVIEW
UMass Amherst CHEM 242 - Building Better Blood

This preview shows page 1 out of 4 pages.

Save
View full document
View full document
Premium Document
Do you want full access? Go Premium and unlock all 4 pages.
Access to all documents
Download any document
Ad free experience
Premium Document
Do you want full access? Go Premium and unlock all 4 pages.
Access to all documents
Download any document
Ad free experience

Unformatted text preview:

Chem242. Int. Inorg. Chem. Spring, 2007 UMass-Amherst Experiment 10 Building Better Blood: Co(Salen) Synthesis and Kinetics Naturally occurring oxygen carriers and storage proteins contain a transition metal ion to which O2 can reversibly bind, typically iron (in the form of ferrous heme in proteins such as myoglobin and hemoglobin) or copper (hemocyanin). In this experiment a simple cobalt complex will be prepared which also reversibly binds dioxygen. Many complexes of this type have been used as models to aid in the understanding of how the proteins function. The complex Co(salen) [where salen = N,N-bis(salicylaldehyde)ethylenediimine] reversibly binds O2, thereby acting as a functional model for myoglobin. As one might imagine, most spectroscopic and measurement techniques are easier to perform and interpret on a molecule which has two orders of magnitude fewer atoms than a protein. NNNNHOOOHOFerrous HemeFe2+NONOCoCo(salen) Figure 1. Ferrous heme is the cofactor which binds O2 reversibly in hemoglobin and myoglobin. Co(salen) is a coordination compound that can also bind O2 reversibly. When Co(salen) was first prepared, it was observed that the red-brown crystals darkened on exposure to air. However, it was not until five years later that it was established that the color change was due to reversible uptake of O2. SalenH2 (figure 2) is a Schiff-base ligand formed by the condensation of two molecules of salicylaldehyde (sal) with ethylenediamine (en). NONOCoCo(salen)NHONOHOOHNH2H2Nensal+ 2salenH2Co(II) Figure 2. Synthesis of Co(salen).Chem242. Int. Inorg. Chem. Spring, 2007 UMass-Amherst Later, it was found that different crystalline forms existed depending on the solvent used in the preparation, and that these crystalline forms had varying capacity for oxygenation in the solid state. This variation in oxygenation has been related to the presence of voids in the crystal lattice, sufficient to allow the passage of molecular oxygen. This suggestion is supported by the x-ray crystal structure determination of the so-called "inactive" form which shows that the structure consists of dimeric units [Co(salen)]2. The active forms of Co(salen) are presumed to contain dimeric units with a more-open lattice packing relative to the inactive form. NONOCoActive structureNONOCoNONOCoNONOCoInactive structure Figure 3. Structures of active and inactive Co(salen) in the solid state. In anaerobic solution, it has been found that, the cobalt(II) may be four, five or six coordinate, depending on the solvent. For example, in a strongly coordinating solvent such as pyridine (py, C5H5N) both [Co(salen)(py)] and [Co(salen)(py)2] exist, while in chloroform, the only species is Co(salen). When 5- or 6-coordinate species can exist, O2 will form a complex with Co(salen). The oxygenated product may be a 1:1 (Co:O2) or a 2:1 (2Co:O2) complex. It is thought that O2 adds as the sixth ligand to a 5-coordinate complex, or replaces one of the coordinating solvent molecules. The final structure may be either a 6-coordinate 1:1 complex, or a 6-coordinate 2:1 complex. It is worth noting that the conventional way to view the formation of an O2-adduct is as a redox process, in which O2 accepts one electron from Co2+, thereby forming superoxide, O2- bound to Co3+. NONOCo2:1 structureNONOCoOOSolSolNONOCo1:1 structureOOSol Figure 4. Two possible structures for the O2 adduct of Co(salen), in which “Sol” represents a coordinating solvent molecule. In this experiment, the inactive form of Co(salen) is prepared. The uptake of dioxygen is then investigated for the complex in DMSO solution to establish whether a 1:1 or a 2:1 complex is formed under these conditions.Chem242. Int. Inorg. Chem. Spring, 2007 UMass-Amherst Week 1: Synthesis H2salen Synthesize the salen ligand by placing 3 mL of 95% ethanol in a test tube that also has a small magnetic stirring bar. Heat the ethanol to boiling in an oil bath on a magnetic stirrer/hotplate. Immediately, with continued heating and stirring, add 0.30 mL (2.8 mmol) of salicylaldehyde and then 0.10 mL (1.4 mmol) of ethylenediamine (98%). Stir the solution for 3 to 4 min and then cool in an ice-water bath to precipitate the yellow salen. Filter and wash your crystals and after air-drying, weigh your product and determine your percent yield. Measure the melting point of your ligand as an additional measure of ligand purity. Co(salen) NOTE: This preparation is sensitive to air, so it MUST be performed under a N2-filled balloon. Add H2salen (0.23 g, 0.86 mmol) to a round-bottom flask containing a stir-bar, and fitted with a reflux condenser; seal the top of the condenser with a septum. To a separate flask, add cobalt(II) acetate tetrahydrate (0.2 g) to 1.5 ml of water while swirling, and affix a septum. Flush both flasks with N2 to create an anaerobic atmosphere; approximately 5-minutes is sufficient. Once both flasks are flushed with N2, add 12 ml of previously degassed ethanol to the H2salen via a needle. Swirl to dissolve the H2salen. Next, add the cobalt acetate solution to the ethanol solution of H2salen via a syringe, and swirl. A brown, gelatinous precipitate should form. Replace the septum with an N2-filled balloon (why is this necessary?). Set the reaction on a sandbath, and heat at a reflux for at least 1 hour. During this period, the initially formed brown "active" complex slowly changes to the brick-red "inactive" complex. Once this has occurred, cool the solution to room temperature, filter to collect the crystals (in air) and wash with 1 ml of ice-cold ethanol. Dry the Co(salen) in a dessicator, then record the yield the following week. Week 2: Kinetics of O2 Absorption by Co(salen) in DMSO Accurately weigh out 50-100 mg of a powder sample of Co(salen) and place it in a side-arm test tube. Larger amounts of Co(salen) make for more accurate results (why is this?) – a good strategy would be to use 1/3 of your material for the first run, and the remaining 2/3 for the second run (where you are more aware of experimental challenges, and are more likely to get good data). Transfer about 5 ml of dimethylsulfoxide (DMSO) to a small test tube that can fit inside the side-arm test tube and lower the tube carefully inside without spillage. (CAUTION: although DMSO is not itself poisonous, it is readily absorbed by the skin and can easily carry other compounds through the skin with it). Connect up the apparatus as shown in the diagram,


View Full Document

UMass Amherst CHEM 242 - Building Better Blood

Download Building Better Blood
Our administrator received your request to download this document. We will send you the file to your email shortly.
Loading Unlocking...
Login

Join to view Building Better Blood and access 3M+ class-specific study document.

or
We will never post anything without your permission.
Don't have an account?
Sign Up

Join to view Building Better Blood 2 2 and access 3M+ class-specific study document.

or

By creating an account you agree to our Privacy Policy and Terms Of Use

Already a member?