Unformatted text preview:

ECGR-6185 Advanced Embedded SystemsDC MotorWorking Principle: Electromagnetism: when a current carrying conductor is placed in the magnetic field there is some mechanical force exerted on the current carrying conductor which is perpendicular to both the conductor and the magnetic filed.The current through a motor is given by the following equation: I = (Vapplied − Vbemf) / Rarmature The mechanical power produced by the motor is given by: P = I * Vbemf The back EMF is dependent on the speed of the motor No Load Speed: Initially Vbemf=0 I=Vapplied/Rarmature Large mechanical force induces a back EMF approx equal to the applied voltage. The motor rotates but does not drive any current. Under Load: Speed (reduces)=>Back EMF(reduces)Speed Control of DC Motor (Using Half Bridge Circuit):Control logic of the micro-controllerSlide 7Slide 8Slide 9The operating Conditions of IR2104 FET DriverOperation The PWM signal generated by a micro – controller is given to IR2104 FET Driver. The IR2104 driver is a high voltage high speed MOSFET driver with dependant high and low side different output Channels (VHO and VLO)Void main() { while (1) { feedback=ad2; while(time_cnt <10000) time_cnt++; // delay loop time_cnt = 0; ta1 = (pwm8 << 8) & 0x0FF00; // set high order (n) } }Stepper Motor: It is a brushless DC Motor whose rotor rotates in discrete angular increments when the stator windings are energized in the programmed manner.Operation: Stepper Motor operation is synchronized by the command pulse signals generated by the Pulse generator. Stepper Motor has a open loop Control SystemControl: For sequential energisation of the stator windings we can either use the pulse generator or micro-controller for generating PWM signals. In order to make pulse per rotation and set the direction of the rotation, two pulse trains of same cycle and phase shifted are supplied by the pulse generator.Relationship between the Input Command Pulses and the motor rotation:Applications: Floppy Disk Drives Flat bed scanners printers PlottersServo Motor: Servos are DC motors with built in gearing and feedback control loop. It has closed loop control system.Working principle: It works on the principle of negative feedback. The Control information is compared with the actual position of the motor Relationship between the I/P command pulses and the actual motor rotation:The servo motor rotation lags behind the command pulses which results in an error signal(Ea,Eb). A deflection counter Compares the number of pulses returned from the encoder(Pe) with the command pulses(Cp). If(Pe>Cp) { driver rotates the motor back word. } If(Pe<Cp) { driver rotates the motor forward } If(Pe=Cp) { motor stops }Applications: CNC machines They use servomotors to make the moton axis of the machine tool follow the desired path. Automobiles To amplify the steering and breaking force applied by the driver.Differences between Servo & Stepper MotorsECGR-6185Advanced Embedded SystemsUniversity Of North Carolina at CharlotteA. Srinivas ReddyStepper/Servo/DC MotorsDC MotorDevice which converts electrical energy into mechanical energy.Components1 Rotor2 Stator3 Commutator4 BrushesArmature:The power producing component, it can be either stator or rotorFunctions:Carries current crossing the field thus creating shaft torqueGenerates Electromagnetic forceWorking Principle: Electromagnetism: when a current carrying conductor is placed in the magnetic field there is some mechanical force exerted on the current carrying conductor which is perpendicular to both the conductor and the magnetic filed.Back EMF: A moving conductor in a magnetic field gets a voltage induced across,which is in opposite polarity to the applied voltageKnown as back EMF. Armature converts the electrical power into the Mechanical torque and transfers it to the lad via shaft.The current through a motor is given by the following equation: I = (Vapplied − Vbemf) / RarmatureThe mechanical power produced by the motor is given by: P = I * Vbemf The back EMF is dependent on the speed of the motorNo Load Speed: Initially Vbemf=0 I=Vapplied/Rarmature Large mechanical force induces a back EMF approx equal to the applied voltage. The motor rotates but does not drive any current. Under Load: Speed (reduces)=>Back EMF(reduces)Speed Control of DC Motor (Using Half Bridge Circuit): Steps1. Calculate the no load speed for the applied voltage.2. Read the speed of the motor under load and provide a feedback to the controller.Control logic of the micro-controllerConvert the analog value of the feedback speed to digital value using A/D converter./* ADC initialization *//* Configure ADC - AN2 (Analog Adjust Pot) */adcon0 = 0x8A; // AN2, repeat sweep mode, software trigger, fAD/2adcon1 = 0x29; // AN2, 10-bit mode, Vref connected.adcon2 = 0x01; // Sample and hold enabled adst=1; // start the A/D ConversionSet the timer to generate PWM signal.#define PWM8_CONFIG 0x67 /* 01100111 value to load into timer A0 mode register ||||||||_ TMOD0,TMOD1: PWM MODE SELECTED ||||||____ MR0: = 1 FOR PWM MODE |||||_____ MR1,MR2: EXT TRIGGER NOT SELECTED |||_______ MR3: SET TO 1 FOR 8BIT PWM ||________ TCK0,TCK1: F DIVIDED BY 8 SELECTED*/ta1mr = PWM8_CONFIG; ta1 = 0x00 // initialize n & m to 0 ta1ic |= 0; ta1s = 1; //start timer A1 .Set the timer to read the A/D value of the feedback voltage for every 1 second. tb0mr = 0x80; tb0=2000; tb0ic = 1; // Timer B0 tb0s = 1; // start timer B0 Set the Pulse width of the PWM signal.void tb0_irq() { if(feedback>=0 && feedback<=1023) // ADC uses 10 bit resolution { RED_LED^=1; pwm8 = 250; } }Typical ConnectionThe Components Regulated power Supply IR2104 Driver Half bridge Circuit using MOSFETs DC motorThe operating Conditions of IR2104 FET Driver MOSFET: MOSFETs are high power application reactive component of all the switching components. It is a high speed switching element.OperationThe PWM signal generated by a micro – controller is given to IR2104 FET Driver. The IR2104 driver is a high voltage high speedMOSFET driver with dependant high and low side different output Channels (VHO and VLO)Red- PWM signal generated from SKP16c62pBlue- High output signal from gate driverYellow- Low output signal from gate driverVoid main(){while (1) {


View Full Document

UNCC ECGR 6185 - Advanced Embedded Systems

Documents in this Course
Zigbee

Zigbee

33 pages

Load more
Download Advanced Embedded Systems
Our administrator received your request to download this document. We will send you the file to your email shortly.
Loading Unlocking...
Login

Join to view Advanced Embedded Systems and access 3M+ class-specific study document.

or
We will never post anything without your permission.
Don't have an account?
Sign Up

Join to view Advanced Embedded Systems 2 2 and access 3M+ class-specific study document.

or

By creating an account you agree to our Privacy Policy and Terms Of Use

Already a member?