(revised, 12/20/05) Speed of Light and Laser Studies Advanced Laboratory, Physics 407 University of Wisconsin Madison, WI 53706 Abstract The speed of light is determined from a time of flight measurement of a short pulse of light. The pulse of light is generated by a dye laser and sent over both a long and a short path and detected by a photomultiplier tube. The velocity of light is then determined from measurements of the light path lengths and the time delay between signals. For the second part, the florescence spectrum of three dyes is measured as a function of wavelength using a photodiode detector.2METHOD This experiment consists of two parts. 1. The short pulse of light emitted from a dye laser is split into two beams. One beam is sent directly to the input of a photomultiplier tube, while the other beam propagates along a much longer path consisting of several mirrors located at the end of the room before being detected by the photomultiplier tube. The speed of light is measured from the time delay between two pulses of light. 3 The florescence spectra of three dyes used in the dye lasers are measured using a photodiode and the grating monochrometer built into the dye laser. The measurement details are described in the following text. There are three Appendices containing apparatus details. A: Dye Lasers, B: Photomultiplier Tubes, and C: Photodiode Detectors. EQUIPMENT 1. Nitrogen pumped Dye laser with 3 dyes. 2. Photomultiplier tube with power supply. 3. Digital Oscilloscope (300 MHz). 4. Assorted plates of glass. 5. 3 adjustable mirrors. 6. Photodiode and power supply. MANUALS 1. VSL-337 Nitrogen Laser and Dye laser Modules, Laser Science, Inc. 2. Photodiode detector manual.3Part 1: Speed of light To measure the speed of light, the time required for a pulse of light to travel a distance will be measured. To produce a high intensity and sufficiently short pulse of light for this measurement a nitrogen pumped dye laser is used. Before starting, you should look up the speed of light and the index of refraction for air, and read the operation manual for the laser. Step 1. Familiarize yourself with the operating principles of a nitrogen-pumped dye laser. Insert the quartz cuvette containing Rhodomine 6G being careful not to touch the surface of the cuvette, and adjust the monochrometer setting to 590. Observe the light pulse on a note card or other surface. Adjust the monochrometer and note that the light quality observed when lasing is different from the fluorescence, which is seen even when the monochrometer is not set to the laser wavelength. Step 2. Familiarize yourself the operating principles of a photomultiplier tube. Turn on the PM tube high voltage (start at 400 volts) and measure the detected current on an oscilloscope with the room lights both on and off. Step 3. Using a fast digital oscilloscope, measure the light pulse from the dye laser by reflecting a small part of the laser light into the PM tube. This is accomplished using one of the plates of glass provided. To trigger the oscilloscope, use both the internal trigger on the signal itself and the external trigger by triggering both the laser and the oscilloscope with a function generator. The noise generated by the switching of the high voltage onto the nitrogen lasers provides a sufficient signal from the PM tube for triggering. How wide is the laser pulse? Step 4. Set up the long path length by using reflections from the three mirrors (down-back-down-back). Direct the final beam onto the PM tube so that both the initial pulse and the second pulse are seen simultaneously on the oscilloscope. If using a digital oscilloscope with pulse Figure 1. Layout for speed of light measurement4averaging, the signal quantity can be greatly improved by summing over multiple pulses. Measure the time separation between the two pulses. How accurate is this measurement? What is the major source of uncertainty in your measurement of the time separation? Step 5. Carefully measure the optical path lengths in the experiment using a plumb bob and a tape measure. Determine the difference in pathlengths for the two laser pulses. What are the major sources of uncertainty in the pathlength measurements? Is this uncertainty more or less important that the time difference uncertainty in step 4? Step 6. Calculate the speed of light in air. Estimate the uncertainty estimate of your measurement. How does it compare with the predicted value?5 Part 2: Florescence of Dyes The dyes used in the dye laser have the interesting quality that once excited they floresce (emit light over a broadband continuum (typically ~10 Angstroms). A nitrogen laser is used to pump the dyes into excited states. By choosing a dye that floresces at a chosen color, lasing can be achieved by placing the excited dye in a resonant cavity. This makes it possible to create a laser at virtually any frequency by choosing an appropriate dye. Here monitoring the laser power with a photodiode and scanning the resonant wavelength of the cavity measures the gain curves of three dyes. Step 1. Read the manual on the photodiode detector. Note that the sensitivity of the photodiode varies with wavelength (the calibration curve is given in the photodiode appendix to this writeup). The calibration curve will be used to correct the measurements and estimate the actual gain in the following steps. Step 2. Turn on the laser with your first dye. Use the plate glass to partially reflect the laser beam into the photodiode detector, and observe the signal directly on the oscilloscope. Be careful not to saturate the photodiode with light (as seen by a “clipped” signal). What determines the pulse-width of the detected signal? Step 3. Vary the monochrometer setting and record the signal level from the photodiode using the oscilloscope. Correct your data for the sensitivity of the photodiode and plot the signal level vs. wavelength. Step 4. Repeat Step 3 for the other two dyes. Plot all three curves on one graph.6APPENDIX A: Dye Laser Gas lasers and solid state lasers can easily be designed for a single frequency oscillation; the output frequency may be tuned continuously over the band-width of the Doppler-broadened gain curve. Unfortunately this tuning range is relatively narrow and the application of these gas