6.012 Microelectronic Devices and Circuits Spring 2007 May 21, 2007 Final Exam (200 points) -OPEN BOOK-Problem #points NAME___________________________________ 1___________ RECITATION TIME___________________________ 2___________ 3___________ 4___________ 5___________ Total______________ General guidelines (please read carefully before starting): • Make sure to write your name on the space provided above. • This exam is open book. You can use any material you wish, except for computers. • All answers should be given in the space provided. Please do not turn in any extra material. • You have 180 minutes to complete the quiz. • Make reasonable approximations and state them, i.e. low-level injection, extrinsic semiconductor, quasi-neutrality, etc. • Partial credit will be given for setting up problems without calculations. NO credit will be given for answers without reasons. • Use the symbols utilized in class for the various physical parameters, i.e. Na, τ, ε, etc. • Every numerical answer must have the proper units next to it. Points will be subtracted for answers without units or with wrong units. • Use the following fundamental constants and physical parameters for silicon at room temperature. ni = 1.0 x 1010 cm-3 kT/q = 0.025V q = 1.6 x 10-19 C εs = 1.0 x 10-12 F/cm εox = 3.45 x 10-13 F/cm 11. (35 points) Figure 1(a) is a common emitter amplifier circuit with a Bipolar Junction Transistor (BJT). V + ↓ iSUP Figure 1(b) emitter base collector WCWBWE NDE NDCNAB BJT1RS BJT RL ± vs ± VBIAS Figure 1(a) The dimensions and doping concentration of this BJT are indicated in Figure 1(b). We will call this transistor BJT1 and its small signal circuit related parameters are labeled ( rπ1 , gm1 , Cπ1 , Cμ1 , ro1 , etc.). For this problem, assume Cπ≈ gmτ F . Assume recombination/generation can only occur at the contacts of the BJTs. (a) Draw the small signal circuit model for the circuit in Figure 1(a). Label gm1, rπ1, Cπ1, Cμ1, ro1 . 2(b) If BJT1 is used in the amplifier and the current iSUP doubles, obtain the ratio of parameters (1) to (5). (1) gm2 x / gm1 (2) rπ 2 x / rπ1 (3) Cπ 2 x / Cπ1 (4) Cμ 2 x / Cμ1 (5) ro2 x / ro1 3Figure 1(c) is the schematic diagram of another BJT, (BJT2). BJT2 has the same dimensions and doping level as BJT1, except half of the emitter region is replaced with polySi. The carrier mobility in the polySi is 20 times less than the mobility in the single crystalline emitter region, while all other parameters remain the same. The purpose of the polySi in the emitter region is to enhance the forward active current gain βF = IICB . WCWBWE NDCNABNDE BJT2polySi Figure 1(c) (c) Obtain the ratio of βF 2/ βF1 . 42. (45 points) You are given the following I-V characteristic for an N-MOSFET withW = L = 100μm , measured at VGS = 2V and VDS = VGS : IDS VGS = 2V, VBS = 0V VDS < 0.1V = VGS ← slope = 70μA /V = gd VDS MOS capacitors fabricated on the same substrate as the N-MOSFETs, with the same n+ polysilicon gate material, gate oxide thickness, and substrate doping, and an area of 2100μm × 100μm (10−4 cm), show the following C-V characteristic: G n+ poly oxide p Si B VGB−1V +1V (a) Find the oxide capacitance per unit area, Cox , and the threshold voltage, VTn , for the N-MOSFET. C Cmax = 35 pF 5(b) Derive an expression for the electron mobility, μn , in the MOSFET in terms of the slope, gd , and the other parameters given above. Calculate μn numerically. (c) Sketch ID vs. VDS on the axes below, for VGS = 2V, VBS = 0V , for the N-MOSFET. Label the values of the saturation voltage, VDS sat , and current, ID sat . Label the regimes of operation. 1 23 VDS ID (VOLTS) 6(d) Calculate the electron velocity at the source end of the channel ( vy (y = 0)) and at the drain end of the channel ( vy (y = L)), for VGS = 2V, VDS = 0.5V, and VBS = 0V . (e) The value of VBS is now changed to −3V . Calculate the new values for VDS sat and IDsat for VGS = 2V and VBS =−3V , assuming that the substrate doping is N = 1017 cm−3 .a 73. (40 points) You are given a common emitter amplifier with RL →∞ shown below. VBIAS ± vOUT + − W 2μm VB +5V RS vS ± MOS Data Bipolar Data VTp =−0.5V β0 = 100 μpCox = 25μA / V 2 VA = 20V λ= 0.05V −1 VCESAT = 0.2V p Assume λp = 0 for parts (a) and (b). (a) Calculate the small signal open circuit voltage gain. Assume VBIAS is set such that IDp = IC = 100μA and both devices are in their constant current operating region. 8(b) Calculate VB and W such that the output swing is between 0.2V and 4.5V . (c) Find Rin , Rout and Avo for this amplifier. 9(d) Calculate the open circuit voltage gain given Rs = 75kΩ . 104. (40 points) You are given a CS-CD voltage amplifier, with its two-port model shown below. +V M 2M1 ↓↓ iSUP 2iSUP1 −V The bias conditions yielded Rin1 →∞ Av1 =−100 Rout1 = 100kΩ Rin2 →∞ Av2 =1 Rout 2 = 1kΩ Rout1 Rout 2 Av2vin2±± Rin2vin2 + − Rin1vin1 + − Av1vin1 (a) Place and label capacitors Cgs1, Cgd1, Cdb1, Cgs2, Cgd 2 and Cdb2 on the two-port model diagram above. Hint: Label the G S D B on the two-port model for each transistor. 11(b) Perform the Miller approximation on all capacitors that are coupling an output and input. Redraw the two-port model and simplify by adding capacitors in parallel. Place and label each capacitor and any applicable circuit parameters. 12(c) Given RS = 1kΩ and RL = 1kΩ , calculate the DC gain vout vs for this two-stage amplifier. (d) Given Cgs1 = Cgs2 = 100 fF Cgd1 = Cgd 2 = 20 fF Cdb1 = Cdb2 = 20 fF use the open circuit time constant method to calculate ω3db . 135. (40 points) You are given a two-stage current amplifier that uses a common-gate stage followed by a common source stage. Assume all backgates are shorted to their respective sources. +5V P −MOSFET N − MOSFET VTp =−1V VTn = 1V 100 2 50 2 10 2 −5V ↓↓ is RS iOUT←2 1 μpCox = 25μA / V 2 μnCox = 50μA / V 2 λ= 0.1V −1 λn = 0V −1 p RL IBIAS =100μA (a) Calculate the DC value IOUT . You may assume all devices are saturated and is = 0 and RS →∞ for this part. 14(b) Calculate the DC voltages at node 1 and node 2. Ignore the signal source is and associated source resistance RS and assume RL = 0 for this calculation. Verify that all three transistors are saturated. 15(c) Given the small signal two-port model for the CG-CS current amplifier shown below, calculate (1) thru (6). RLRout
View Full Document
Unlocking...