Unformatted text preview:

1Texas A&M UniversityECEN 449 – Microprocessor System DesignPulse Modulation2Texas A&M UniversityObjectives of this Lecture Unit• Get familiar with pulse based communication– Different pulse modulation schemes– Applicability of these to different design scenarios3Texas A&M UniversityModulation and Communication• When we have to communicate information over a medium, we typically – Modulate the signal before transmission by the sender– Then demodulate the signal at the receiving end to retrieve the information• Why do this?– The modulated signal can be transmitted with low loss– Interference with other communications is avoided– Receiving antennas can be made quite small– Multiple signals can be multiplexed• Typical modulation schemes – amplitude, frequency, phase, code4Texas A&M UniversityWhat is Pulse Modulation• Pulse modulation involves communication using a train of recurring pulses.• Common means of modulating data in digital communication – Key advantage is that I can send multiple signals using Time Division Multiplexing• There are several pulse modulation techniques – Pulse Amplitude Modulation– Pulse Width Modulation– Pulse Code Modulation– Pulse Position Modulation5Texas A&M UniversityPulse Amplitude Modulation (PAM)• Message information encoded in the form of the amplitude of pulses.• Pulse transmitted every T seconds, amplitude of the pulse is quantized to Q values, for PAM-Q.• Example shown above is the PAM encoded (blue) signal corresponding to a sinusoidal (red) input.6Texas A&M UniversityPulse Amplitude Modulation• Examples: – Telephone modems faster than 300 bits/sec use PAM– Ethernet uses PAM. • 100BASE-T2 as well as 1000BASE-T use PAM-5• To achieve full-duplex operation, we can do one of two things– Use some kind of carrier sensing (as in Ethernet, which uses Carrier Sense Multiple Access)– Or use some flavor of Time Division Multiple Access.7Texas A&M UniversityPulse Width Modulation (PWM)• Here we modulate the width of pulses (or their duty cycle) to convey information.• Example above shows the PWM signal (bottom picture) corresponding to a sinusoidal signal (top picture). The PWM signal is typically generated using a sawtooth waveform and a comparator8Texas A&M UniversityPulse Width Modulation • Popular in digital circuits– Generation of PWM signal easy, demodulation typically uses counters and digital-to-analog converters (DACs)• Three flavors of PWM– Pulse center is in the center of the time window– Pulse leading edge coincides with leading edge of time window, and the trailing edge is modulated– Pulse trailing edge coincides with trailing edge of the time window, and the leading edge is modulated• Applications– Voltage regulators– Class D audio amplifiers (feed PWM signal to speaker after filtering to block carrier), which are highly efficient.9Texas A&M UniversityPulse Code Modulation (PCM)• Means to represent an analog signal in a digital manner• Sample the analog signal every T seconds, into P values. – P is usually a power of two.• Transmit log2P bits every T seconds (can do compression also)• Typically sampling is done via an ADC (Analog to Digital Converter).• Many such PCM datastreams can be multiplexed on to a high bandwidth medium in a Time Division Multiplexing (TDM) fashion.– Example voice signals sent over a phone network, or data sent over an optic fiber10Texas A&M UniversityPulse Code Modulation• Demodulation is done by collecting log2P entries, and feeding them to a Digital to Analog Converter (DAC).– Possibly need to do decompression before this.• Applications– Digital audio in computers and CDs– Straight PCM not used in video standards (DVD, DVR) since it needs a high bitrate.• Some PCM techniques transmit the difference between two adjacent samples, rather than the raw sample values. This effectively compresses the transmitted data.11Texas A&M UniversityPulse Position Modulation (PPM)• Suppose I want to send one of M message bits every T seconds.• PPM modulates the message by transmitting a single pulse in one of 2Mtime slots– Each time slot is T/2Mseconds long• Problematic for communication media where multi-path interference dominates– Urban environments– Media which exhibit frequency-dependent fading12Texas A&M UniversityPulse Position Modulation• Commonly used in communication over optic fibers– Multi-path fading is minimal– No need for Phase-Locked Loop at the receiver (i.e. can use non-coherent receiver). Coherent receivers are prohibitively expensive for optical communication systems.• Also used in communication for RC aircraft/cars etc.– The demodulation is very simple and easy, allowing for a low-cost receiver.– Fancier RC systems use PCM (more expensive)13Texas A&M UniversityPulse Frequency Modulation (PFM)• Conceptually, we could do PFM as well. • Pulses of constant amplitude are generated, at a rate which is modulated by the signal frequency.• Problem: arrival rate of pulses is random, and hence demodulation is hard. • Therefore PFM is mostly a


View Full Document

TAMU ECEN 449 - pulse

Download pulse
Our administrator received your request to download this document. We will send you the file to your email shortly.
Loading Unlocking...
Login

Join to view pulse and access 3M+ class-specific study document.

or
We will never post anything without your permission.
Don't have an account?
Sign Up

Join to view pulse 2 2 and access 3M+ class-specific study document.

or

By creating an account you agree to our Privacy Policy and Terms Of Use

Already a member?